![X-NUCLEO-IHM02A1 - Two axis stepper motor driver expansion board based on the L6470](https://kamami.pl/66234-large_default/x-nucleo-ihm02a1-two-axis-stepper-motor-driver-expansion-board-based-on-the-l6470.jpg)
![X-NUCLEO-IHM02A1 - Two axis stepper motor driver expansion board based on the L6470](https://kamami.pl/66234-large_default/x-nucleo-ihm02a1-two-axis-stepper-motor-driver-expansion-board-based-on-the-l6470.jpg)
zł69.50 tax excl.
Two axis stepper motor driver expansion board based on the L6470 for STM32 Nucleo
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
The X-NUCLEO-IHM02A1 is a two axis stepper motor driver expansion board based on the L6470. It provides an affordable and easy-to-use solution for low voltage motor control driving for stepper motors in your STM32 Nucleo project.
The expansion board includes two L6470s, a fully-integrated micro stepping motor driver used to control stepper motors by means of high-end motion control commands received through SPI. It is capable of driving one or two stepper motors when plugged into an STM32 Nucleo board.
This board is equipped with Arduino UNO R3 connectors and the layout is also compatible with ST morpho connectors. One or more of these expansion boards can be plugged into an STM32 Nucleo board to control one or more stepper motors.
Each SPI peripheral of each L6470 is connected in a daisy chain configuration.
The X-NUCLEO-IHM03A1 plate allows the control of a high-power stepper motor; the maximum current of the phase is 10A rms, additionally the controller enables execution up to 1/128 step and has a number of protections. X-NUCLEO-IHM03A1
Shield for STM32 Nucleo that allows you to add the possibility of operating a three-phase brushless motor (BLDC) or synchronous permanent magnet (PMSM). It uses the L6230 chip for control. X-NUCLEO-IHM07M1
Extension board X-NUCLEO-IHM04A1 for STM32 Nucleo, with dual brush motor controller, operating based on the L6206 system
The STM32 Nucleo expansion board allows you to control a bipolar stepper motor. The maximum phase current is 2.8A RMS, the controller has overheat protection and overcurrent protection
The X-NUCLEO-IHM03A1 plate allows the control of a high-power stepper motor; the maximum current of the phase is 10A rms, additionally the controller enables execution up to 1/128 step and has a number of protections. X-NUCLEO-IHM03A1
The X-NUCLEO-S2868A1 expansion board is based on the S2-LP radio and operates in the 868 MHz ISM frequency band. The expansion board is compatible with ST morpho and Arduino UNO R3 connectors
Expansion board with LCD TFT 2.2 "display for STM32 Nucleo sets. Equipped with SPI NOR Flash 64Mbit memory for storing images and a joystick for GUI navigation. STMicroelectronics X-NUCLEO-GFX01M2
The P-NUCLEO-IOD01A1 is an STM32 Nucleo pack composed of the NUCLEO-L073RZ development board, the STEVAL-IOD003V1 evaluation board and the X-NUCLEO-IKS01A2 expansion board
The X-NUCLEO-NFC03A1 is an NFC card reader evaluation board based on CR95HF / ST25R95-VMD5T to enable expansion of the STM32 Nucleo boards
Extension board with distance sensor ToF VL53L1, The sensor has a range of up to 400 cm. The kit includes 2 modules with sensors that can be connected via a 10-pin connector. The shield is compatible with STM32 Nucleo boards and has an Arduino UNO R3 connector. STMicroelectronics X-NUCLEO-53L1A2
P-NUCLEO-IOD02A1 is an STM32 Nucleo kit consisting of NUCLEO-L452RE (IO-Link stack), X-NUCLEO-IOD02A1 (IO-Link physical layer) and X-NUCLEO-IKS02A1 (sensor module). The kit constitutes a full IO-Link device. P-NUCLEO-IOD02A1
Expansion board with BlueNRG-M0 module compatible with Bluetooth v4.2. It is compatible with the ST morpho connector system (unmounted) and Arduino UNO R3. Communication with the module is via the SPI interface. STMicroelectronics X-NUCLEO-IDB05A2
KAmodNFC is an expansion board with M24LR64E-R chip – dynamic tag with 64kb EEPROM memory and dual communication interface (I2C/RF). On board is placed also signalization of energy harvesting function, which is in M24LR64E-R chip embedded.
Time-of-Flight VL53L3CX Distance Sensor Expansion Board. The set is designed to measure distances and detect gestures. Distance measurement was carried out using VL53L3CX laser sensors. STMicroelectronics X-NUCLEO-53L3A2
Expansion board with LCD TFT 2.2" display for STM32 Nucleo-144 sets. Equipped with SPI NOR Flash 64Mbit memory for storing images and a joystick for GUI navigation. STMicroelectronics X-NUCLEO-GFX02Z1
A kit consisting of STM32 NUCLEO-F401RE board with STM32F401RE microcontroller and X-NUCLEO-53L4A1 board with VL53L3CD ToF distance sensor. STMicroelectronics P-NUCLEO-53L4A1
Expansion board equipped with VL6180 distance sensor, based on FlightSense technology. The set is designed to measure distances and detect gestures. X-NUCLEO-6180A1
Expansion board with ToF VL53L4CX distance sensor with a range of up to 6 m. The shield is compatible with STM32 Nucleo boards. STMicroelectronics X-NUCLEO-53L4A2
The set consists of the STM32 NUCLEO-F401RE board with the STM32F401RE microcontroller and the X-NUCLEO-53L5A1 board with the VL53L5CX ToF distance sensor. STMicroelectronics P-NUCLEO-53L5A1
Expansion board for STM32 Nucleo designed for applications using MEMS analog microphones. The board is compatible with STM32 Nucleo and Arduino UNO R3 connectors. STMicroelectronics X-NUCLEO-AMICAM1
No product available!
Two axis stepper motor driver expansion board based on the L6470 for STM32 Nucleo