X-NUCLEO-AMICAM1 - expansion board for MEMS analog microphones

The P-NUCLEO-IOD01A1 is an STM32 Nucleo pack composed of the NUCLEO-L073RZ development board, the STEVAL-IOD003V1 evaluation board and the X-NUCLEO-IKS01A2 expansion board

ToF VL53L7CX distance sensor expansion board with a 64-pixel array, a range of up to 3.5 m and a viewing angle of up to 90°. The overlay is compatible with STM32 Nucleo boards. STMicroelectronics X-NUCLEO-53L7A1

Shield for STM32 Nucleo that allows you to add the possibility of operating a three-phase brushless motor (BLDC) or synchronous permanent magnet (PMSM). It uses the L6230 chip for control. X-NUCLEO-IHM07M1

STM32 Nucleo expansion board designed to provide an application for the 16 channel LED driver LED1642GW. Depending upon the end application, RGB or single color LEDs can be connected to the board. Separate brightness control is possible for each channel. It is compatible with the STM32 Nucleo board family and equipped the Arduino™ UNO R3 connector layout. X-NUCLEO-LED16A1

The P-NUCLEO-IOM01M1 is an STM32 Nucleo pack composed of the STEVAL-IOM001V1 and the NUCLEO-F446RE board. The STEVAL-IOM001V1 is a single IO-Link master PHY layer (L6360) while the NUCLEO- F446RE runs an IO-Link stack rev 1.1

Two axis stepper motor driver expansion board based on the L6470 for STM32 Nucleo

The X-NUCLEO-NFC03A1 is an NFC card reader evaluation board based on CR95HF / ST25R95-VMD5T to enable expansion of the STM32 Nucleo boards

The X-NUCLEO-S2868A1 expansion board is based on the S2-LP radio and operates in the 868 MHz ISM frequency band. The expansion board is compatible with ST morpho and Arduino UNO R3 connectors

A kit consisting of STM32 NUCLEO-F401RE board with STM32F401RE microcontroller and X-NUCLEO-53L4A1 board with VL53L3CD ToF distance sensor. STMicroelectronics P-NUCLEO-53L4A1

Expansion board with L6474 stepper motor driver. It is equipped with a connector compatible with Arduino Uno R3 and STM32 Nucleo. STMicroelectronics X-NUCLEO-IHM01A1

Shield with MEMS sensors: accelerometer, gyroscope, magnetometer, pressure, humidity and temperature sensor. Shield is designed to work with plates from the STM32 Nucleo family (connector in accordance with the Arduino UNO R3 standard). Sensors use I2C interface for communication. STMicroelectronics X-NUCLEO-IKS01A3

The STM32 Nucleo expansion board allows you to control a bipolar stepper motor. The maximum phase current is 2.8A RMS, the controller has overheat protection and overcurrent protection

Board with digital outputs designed to work with STM32 Nucleo. It is based on the IPS1025HF single high-side switch arrangement. STMicroelectronics X-NUCLEO-OUT15A1

Expansion board for STM32 Nucleo with NFC card reader based on ST25R3916B chip. The board includes a connector compatible with the Arduino Uno R3. STMicroelectronics X-NUCLEO-NFC08A1

Extension board with distance sensor ToF VL53L1, The sensor has a range of up to 400 cm. The kit includes 2 modules with sensors that can be connected via a 10-pin connector. The shield is compatible with STM32 Nucleo boards and has an Arduino UNO R3 connector. STMicroelectronics X-NUCLEO-53L1A2

Extension board for SMT332 Nucleo with VL6180X sensor, allowing to measure ambient lighting, zoom and recognition of gestures. On the PCB, outside the sensor, there is also a four-digit LED display and connectors for additional sensors