zł60.11 tax excl.
Wireless breakout based on the ST67W611M1A6B, providing 2.4GHz WiFi 6 and Bluetooth LE 5.4 connectivity for STM32 microcontrollers. Supports SPI and UART host interfaces, 3.3V supply and a built-in PCB antenna. Soldered 333353
The device ST67 Wireless Breakout features the STMicroelectronics ST67W611M1A6B wireless module and is designed for use with STM32 microcontrollers. The module operates as a dedicated wireless communication coprocessor, allowing wireless connectivity to be handled independently of the application running on the main microcontroller. It supports simultaneous 2.4GHz WiFi 6 and Bluetooth LE 5.4 connectivity.
The WiFi interface supports IEEE 802.11b/g/n/ax standards and provides TCP throughput of up to 17Mbps. Supported operating modes include STA, SoftAP and simultaneous STA + SoftAP, together with WPS, WEP, WPA, WPA2 and WPA3 security mechanisms. The module also supports MU-MIMO, OFDMA and Target Wake Time technologies. Bluetooth LE 5.4 provides data rates of up to 2Mbps and supports peer-to-peer, broadcast and mesh communication. Wireless communication is handled through a built-in PCB antenna.

The board operates from a 3.3V supply and communicates with the host microcontroller through SPI at up to 40MHz or UART at up to 2Mbps. IO lines can operate at either 1.8V or 3.3V. The board includes a 32.768kHz oscillator and power supply decoupling capacitors. Deep-sleep current consumption is 90µA. The board features an 11-pin male header and a breadboard-compatible design. Factory-installed X-CUBE-ST67W61 software allows quick startup with the module.
Data sheet
LPT100 WiFi Module Mother Board
An integrated module combining WiFi, Bluetooth 4.0 and FM radio. It has derived SDIO, UART and PCM interfaces. Ampak AP6335
ESP8266 based Arduino board for ArduCAM mini camera modules while keeping the same form of factors and pinout as the standard Arduino UNO R3 board. ArduCAM B0082
No product available!
ArduCAM CC3200 UNO Board CC3200 UNO is full featured development board almost like a combination of CC3200 Launchpad plus CC3200CAMBOOST pack from TI while keeping exactly the same size as Arduino UNO and pin out. B0078
Comprehensive development platform for Espressif ESP32 a WiFi-compatible microcontroller and nearly 30 I/O pins. DEV-13907
Wifi module with ESPR8266 ESPRESSIF for communication in the 2.4 GHz band. It is powered by a voltage from 3 V to 3.6 V, available in an SMD enclosure. ESP-WROOM-02
The ESP32 WiFi and Bluetooth module has a dual-core 32-bit MCU that integrates WiFi HT40 and Bluetooth / BLE 4.2 technology. Designed for mobile devices and Internet of Things (IoT) applications. DFRobot TEL0111
The low-power consumption micro-controller intentionally designed for Internet of Things (IoT) projects. The board integrates a Dual-Core ESP-WROOM-32 module, which supports MCU and Wi-Fi &Bluetooth dual-mode communication. DFR0478
An IoT module that combines a microcontroller with an ARM-Cortex M3 core, WiFi and NFC. It can be programmed in the Arduino IDE or in the Micropython language. DFRobot DFR0477
Evaluation set for IoT applications. Rich set of equipment in such peripheral systems as WiFi, OLED display, headphones, microphone, sensors (temperature, humidity, motion, pressure) make it a complete tool that will be used in many projects. DFRobot DFR0512
Connect your Arduino-compatible to the Internet with this WiFi shield that features the FCC-certified ATWINC1500 module from Atmel. Adafruit 3653
Connect your Arduino-compatible to the Internet with this WiFi shield that features the FCC-certified ATWINC1500 module from Atmel. Adafruit 3654
WIFI-LPT100 Eval Kit module enables UART data transmission via WiFi, ultra low power consumption, encrypted communication
No product available!
WIFI-LPB100-A module Eval Kit enables UART data transmission via WiFi, ultra low power consumption, encrypted communication
No product available!
IoT DFRobot Gravity UART OBLOQ module for working with Microsoft Azure. DFRobot TEL0118
WiFi module based on ESP8266. It has an embedded antenna and 0.96 "OLED display. The module can be programmed in Lua (under NodeMCU firmware control) or in the Arduino IDE. Provides 12 GPIO lines.
Wireless breakout based on the ST67W611M1A6B, providing 2.4GHz WiFi 6 and Bluetooth LE 5.4 connectivity for STM32 microcontrollers. Supports SPI and UART host interfaces, 3.3V supply and a built-in PCB antenna. Soldered 333353