![JTAG SMT2 JTAG SMT2](https://kamami.pl/16858-large_default/jtag-smt2-surface-mount-programming-module.jpg)
![JTAG SMT2 JTAG SMT2](https://kamami.pl/16858-large_default/jtag-smt2-surface-mount-programming-module.jpg)
zł237.70 tax excl.
JTAG SMT2 Surface-Mount Programming Module
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
JTAG SMT2 Surface-Mount Programming Module, Digilent, RoHS
The Joint Test Action Group (JTAG)-SMT2 is a compact, complete and fully self-contained surface-mount programming module for Xilinx field-programmable gate arrays (FPGAs). The module can be accessed directly from all Xilinx tools, including iMPACT, Chipscope, and EDK. Users can load the module directly onto a target board and reflow it like any other component.
The JTAG-SMT2 uses a 3.3V main power supply and a separate Vref supply to drive the JTAG signals. All JTAG signals use high speed, 24mA, three-state buffers that allow signal voltages from 1.8V to 5V and bus speeds of up to 30MBit/sec. The JTAG bus can be shared with other devices as systems hold JTAG signals at high-impedance, except when actively driven during programming. The SMT2 module is CE certified and fully compliant with EU RoHS and REACH directives. The module uses a standard Type-A to Micro-USB cable available for purchase from Digilent, Inc.
Users can connect JTAG signals directly to the corresponding FPGA signals as shown in Figure 1. For best results, mount the module adjacent to the edge of the host PCB over a ground plane. Although users may run signal traces on top of the host PCB beneath the SMT2, Digilent recommends keeping the area immediately beneath the SMT2 clear. Note: Keep the impedance between the SMT2 and FPGA below 100 Ohms to operate the JTAG at maximum speed. The SMT2 improves upon the SMT1 with the addition of three general purpose IO pins (GPIO0 – GPIO2) and support for interfacing IEEE 1149.7-2009 JTAG targets in both 2 and 4-wire modes.
Key Features:
Download:
Code: 210-251
No product available!
USB compatible cable for in-circuit configuration and programming of all Xilinx devices
The development board allows you to easily use the capabilities of ESP32 (Wi-Fi + Bluetooth BLE) from Espressif. There is a USB / UART converter on the board, and most of the GPIO line of the ESP-WROOM-32D module has been connected to pins with a pitch of 2.54mm. ESP32-DevKitC V4
The module with the EEPROM 24LC256 memory chip with a capacity of 32 kB. It is supplied with the voltage ranging from 2.5 V to 5.5 V and communicates via the I2C interface (Gravity connector). DFRobot DFR0117
GPS module with u-blox ZED-F9R. Uses Automotive Dead Reckoning (ADR) technology. Provides highly accurate and continuous positioning by combining the 3D IMU sensor, vehicle dynamics model, correction data and GNSS measurements. SparkFun GPS-16475
No product available!
Starter kit with STM32F411RE microcontroller (512 kB Flash, Cortex-M4), with ST-Link / v2 programmer-debugger. Modified version compatible with the original Nucleo. Waveshare XNUCLEO-F411RE
Demonstration kit for M24LRxx Dual Interface EEPROMs, STM, RoHS
Module with WiFi and Bluetooth Espressif ESP32 WROOM. It integrates a set of peripheral devices - capacitive touch sensors, Hall sensors, SD card interface, Ethernet, fast SPI, UART, I2S and I2C. SparkFun WRL-17381
No product available!
Integrated single board computer with Cyclone V SoC core. SoC SoM includes DDR3 memory, Flash memory, energy management system, common interface controllers and disc software (BSP). Terasic P0581
No product available!
A new game controller that is similar to the steering wheel available for the Nintendo Wii. It is built using the USB IO BOARD and an auxiliary motion sensor, and allows you to play many games available for mobile phone that would normally use the phone’s gyroscope
No product available!
A small module, matching the breadboard, containing a 32-bit microcontroller with ARM Cortex M7 core. PJRC TEENSY40
Waterproof strip with RGB LED diodes, 1 m long (30 LEDs per meter). The LEDs are mounted on a flexible white PCB, the tape has a Grove connector. Seeed Studio 104020108
Evaluation board with the Intel Agilex SoC system with 1400 thousand. logical elements. The module has two DDR4 SO-DIMM memory slots (up to 32 GB), QSFP28 connector, PCIe Gen 4x16, built-in USB-Blaster II and FMC/FMC+ connectors for expansion. TerasIC Apollo Agilex SOM (P0714)
No product available!
J-Link 9-pin Cortex-M Adapter, RoHS, Segger
JST-SH 4-pin SMD connector for modules with Qwiic connectors. Pins\' pitch is 1 mm. Qwiic allows you to connect sensors via the I2C bus. SparkFun PRT-16766
Radio receiver module operating at 433 MHz. It is equipped with Gravity connectors and communicates via a digital interface. DFRobot TEL0142
Hi-Speed JTAG/SWD Emulator for ARM7/9, Cortex and Renesas RX cores with USB interface, Segger
JTAG SMT2 Surface-Mount Programming Module