ZedBoard Zynq-7000

FPGA development board with Xilinx Artix-7 FPGA. Equipped with 24 GB of DDR3 SDRAM memory and an Edge Rate Rugged High-Speed male connector. Numato Lab NLFX1009

Base plate for Trenz Electronics 4x5 cm modules, e.g. TE0741, TE0712. The board allows connecting to the module interfaces: USB, Ethernet, JTAG. TE0705-04

Industrial SoC module integrating Xilinx Zynq 7020 SoC, Gigabit Ethernet transceiver, 1 GB DDR3 SDRAM and 32 MB Flash memory. Trenz Electronic TE0720-03-2IF

A programming platform designed on the basis of the Xilinx system-on-chip system Zynq-7000 (APSoC). The Zynq-7000 architecture integrates the ARM Cortex-A9 667 MHz processor with the Xilinx 7 FPGA chip. Digilent Cora Z7-07S (410-370)

Development kit with FPGA Artix-7 100T equipped with 512 MB DDR3 memory, Zmod port and Pmod ports and two-channel ADC Zmod Scope 1410-105 converter. Digilent 471-047

Module with Xilinx Kintex-7 XC7K70T-2IF chip, 32MB FLASH memory and very fast data transmission systems. Everything is on a small 4 x 5 cm plate. TE0741-03-070-2CF

Development kit with Artix-7 100T FPGA chip, compatible with the PC/104 standard. The set is equipped with 512 MB DDR3 memory, Zmod port and Pmod ports. Digilent 410-398

FPGA Evaluation Kit based on the XC7A100T-1CSG324C chip from the Artix-7 FPGA Xilinx family. Nexys works with Xilinx ISE and Vivado software . Equipped with numerous interfaces and sensors allows you to develop projects without attaching additional elements to the set. Digilent 410-292

Platform with the AD9364 radio transmitter and receiver and the Xilinx Spartan-6 XC6SLX75 FPGA chip. Digilent 6002-410-023

FPGA development board with Xilinx Kintex-7 FPGA chip with 4 GB DDR3L SDRAM memory. Equipped with a fast USB 3.1 interface. Numato Lab NLFX1004-C

Evaluation kit with the Zynq-7000 APSoC chip integrating the ARM Cortex-A9 based processor with the Artix-7 FPGA chip. Provides two SYZYGY interface connectors enabling cooperation with fast modular systems. The set works under the control of Linux. Digilent Eclypse Z7 (410-393)

Module with Xilinx Artix-7 100T system and 32MB FLASH memory. TE0725LP-01-100-2L

Module with Xilinx Artix-7 200T system, FLASH memory with 32 MB capacity, 1 GB RAM memory and 10/100 Mbit Ethernet controller. Everything fits on a small 4 x 5 cm tile. TE0712-02-200-2C

Module with Xilinx Artix-7, USB 3.0 / FIFO bridge, 1GB DDR3L SDRAM memory, 32 MB flash memory and pulse converters to ensure all voltages in the system. Everything fits on a small 4 x 5 cm tile. TE0713-01-200-2C

Module with Xilinx Artix-7 35T, FLASH memory with 32 MB capacity. Everything fits on a small 4 x 5 cm tile. TE0711-01-35-2C

Evaluation kit equipped with Xilinx Artix 7 XC7A35T-1C FPGA chip and 256 MB DDR3 RAM. The kit is supported by Vivado and the Verilog and Lucid languages. SparkFun DEV-16527