MAX4824PMB1
ID: 198556
5906623494699
zł153.92
Tax included
zł125.14 tax excl.
Maxim Octal Relay Driver - Peripheral Module
MAX4824PMB1 Peripheral Module
Refer to the MAX4824 IC data sheet for detailed information regarding operation of the IC.
Description
The MAX4824PMB1 peripheral module provides the necessary hardware to interface the MAX4824 8-channel relay driver to any system that utilizes PmodTM-compatible expansion ports configurable for GPIO communication. Each independent channel in the IC features a 2.7I(typ) on-resistance and is guaranteed to sink 70mA (min) of load current. A zener kickback-protection circuit significantly reduces recovery time in applications where switching speed is critical. When driving relays, a unique power-save mode allows relay current to be reduced to a level just above the relay hold-current threshold. This mode keeps the relay activated while significantly reducing the power consumption.Refer to the MAX4824 IC data sheet for detailed information regarding operation of the IC.
Features
- Eight Independent Output Channels Capable of 70mA Sink Current
- Guaranteed 5I (max) RON
- Drive Eight Relays (or Other Loads) Independently
- 4-Bit Parallel Interface (SPI Version of IC also Available)
- 12-Pin Pmod-Compatible Connector (GPIO)
- Example Software Written in C for Portability
- RoHS Compliant
- Proven PCB Layout
- Fully Assembled and Tested
198556
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
+3.3V/+5V, 8-Channel Relay Drivers with Fast Recovery Time and Power-Save Mode, TQFN20, Maxim, RoHS
zł46.72
24h
Available quantity: 1
Available
Other products in the same category (16)
The Pmod CAN is a CAN 2.0B controller with an integrated transceiver. The embedded Microchip MCP25625 chip connects directly to the physical CAN bus and meets automotive requirements for high-speed (1 Mb/s), low quiescent current, electromagnetic compatibility, and electrostatic discharge. Digilent 410-353
zł104.13
3 weeks
No product available!
Available
Available
Available
Available
relative humidity sensor with integrated temperature sensor for highly accurate measurements at low power. With the TI HDC1080, you can determine the relative humidity of the environment with up to 14 bits of resolution. Digilent 410-347
zł87.98
3 weeks
No product available!
The Pmod BLE module is a Bluetooth module with powerful capabilities. Thanks to communication via the UART port, the module can be connected to any platform equipped with this interface. The module is equipped with the Roving Networks RN4870 system, in which a full Bluetooth interface is built-in. Digilent 410-359
zł167.51
24h
Available quantity: 1
Available
Available
Accessory board designed to provide students a cost-effective, portable, and engaging platform for teaching electronics. With a myDAQ / myRIO, NI Multisim, and a myDigital, you\'ll have everything needed to allow students to design, construct, test basic analog and digital designs. 6002-410-006
zł620.57
3 weeks
No product available!
Available
The Pmod SF3 provides users with 32 MB of non-volatile memory through the use of Micron\'s NOR Flash memory (N25Q256A). By using the SPI protocol, users can both write to and read from the flash memory. Digilent 410-340
zł127.82
3 weeks
No product available!
Evaluation Board with CN0332, Magnetoresistive (MR) Rotational Speed Sensor, Analog Devices, RoHS
zł243.54
24h
Available quantity: 1
Available
Available
No product available!
Available
PmodCMPS2 is a module with a digital magnetometer based on the Memsic MMC34160PJ system. It has a resolution of 0.5 mG (within ± 16) and accuracy up to 1 °. For communication with the module, an I2C interface is provided on the 6-pin Pmod connector. Digilent 410-355
zł38.82
3 weeks
No product available!
Maxim Octal Relay Driver - Peripheral Module