.png)
PYNQ-Z2 Python - FPGA development kit
ID: 574762
5906623407712
zł1,449.00
Tax included
zł1,178.05 tax excl.
Development board FPGA with ZYNQ XC7Z020-1CLG400C system, built-in USB, audio / video interfaces, JTAG programmer and compatible connector Arduino UNO R3 and Raspberry Pi. The set works with the open-source PYNQ project that combines FPGA with Python. TUL PYNQ-Z2
Description
Set PYNQ-Z1 is designed for use with a new, open-sourceową structure PYNQ , allowing developers to use the capabilities of SoC Xilinx Zynq (APSoC), without having to design programmable logic - instead, systems SoC are programmed using Python , and the code it is developed and tested directly on PYNQ-Z2. Logic circuits are imported as hardware libraries and programmed by the API practically in the same way as software libraries.
PYNQ-Z2 is a programmable FPGA board for embedded systems, natively supporting multimedia using audio and video interfaces on board. The board was designed to easily extend its capabilities using Pmod modules, Arduino shields, Raspberry Pi shields, Grove extensions, as well as using the shared GPIO ports. The possibilities of the PYNQ-Z2 can also be extended using USB devices - such as Wi-Fi cards, Bluetooth modules or cameras.
properties
- The ZYNQ XC7Z020-1CLG400C system
- Dual-core Cortex-A9 processor with 650 MHz frequency
- DDR3 memory controller with 8 DMA channels and 4 AXI3 slaves with high performance
- High bandwidth peripheral controllers: 1G Ethernet, USB 2.0, and SDIO
- Peripheral controller with low bandwidth: SPI, UART, CAN, I2C
- Programmable with JTAG, Quad-SPI flash and MicroSD card
- Programmable logic corresponding to the Artix-7 FPGA
- 13,300 logical blocks, each with four 6-input LUTs and 8 flaps
- 630 KB of fast RAM
- 4 clock management boards, each with a loop (PLL) and a mixed mode clock (MMCM)
- 220 DSP blocks
- Built-in analog-digital converter (XADC)
- Memory
- 512 MB DDR3 memory with 16-bit bus at 1050 Mb / s
- 16 MB Quad-SPI Flash with pre-programmed 48-bit unique identifier worldwide compatible with EUI-48/64
- MicroSD socket
- USB and Ethernet
- Gigabit Ethernet PHY
- Micro USB-JTAG programming circuit
- Micro USB-UART bridge
- USB 2.0 OTG PHY (only supports host)
- Sound and video
- HDMI port (input)
- HDMI port (output)
- I2S interface with 24-bit digital-to-analogue converter with 3.5mm TRRS socket
- Line input with 3.5 mm socket
- Switches, buttons and LEDs
- 4 buttons
- 2 slide switches
- 4 LEDs
- 2 RGB LEDs
- Expansion connectors
- Two standard Pmod - 16 I / O FPGA ports (8 common pins with Raspberry Pi connector)
- Arduino Shield connector - 24 I / O FPGAs and 6 single analogue inputs 0-3,3V to XADC
- Raspberry Pi connector - 28 I / O FPGA (8 common pins with Pmod A port)
- Power
- Powered from external USB or 7-15 V power supply
574762
You might also like
The board features a Zynq XC7Z020, Ethernet, HDMI in/out, MIC in, Audio out, Arduino Interface, 2 Pmods, 16 pin GPIO header, user LEDs, pushbuttons and Switches. 6003-410-0
Regular pricezł1,212.60zł1,008.82
24h
Available quantity: 1
Available
Other products in the same category (16)
Development board FPGA with ZYNQ XC7Z020-1CLG400C system, built-in USB, audio / video interfaces, JTAG programmer and compatible connector Arduino UNO R3 and Raspberry Pi. The set works with the open-source PYNQ project that combines FPGA with Python. TUL PYNQ-Z2
zł1,449.00
4 weeks
No product available!
DIP module with 36 pins, based on the Xilinx Spartan-7 FPGA chip. Provides 32 digital I/O signals and 2 analog input signals. The pins are spaced 100 miles (2.54 mm), making Cmod S7 perfect for use with breadboards. Digilent Cmod S7
zł538.89
24h
Available quantity: 1
Available
Development board FPGA PYNQ-Z1 and accessor set. Includes base plate, power supply, cables and SD card with system image for PYNQ-Z1. Digilent 240-114-1
Regular pricezł2,335.40zł1,899.00
24h
Available quantity: 2
Available
Evaluation kit equipped with Xilinx Artix 7 XC7A35T-1C FPGA chip and 256 MB DDR3 RAM. The kit is supported by Vivado and the Verilog and Lucid languages. SparkFun DEV-16527
zł791.64
3 weeks
No product available!
Platform with the AD9364 radio transmitter and receiver and the Xilinx Spartan-6 XC6SLX75 FPGA chip. Comes with enclosure. Digilent 471-042
zł9,998.93
24h
Available quantity: 1
Available
Development board with Xilinx Artix 7 chip equipped with M.2 connector. It offers a PCIe Gen2 interface and DDR3 2 Gb memory. Numato Lab NLFX1006
zł2,377.48
3 weeks
No product available!
FPGA development board with Xilinx Kintex-7 FPGA chip with 4 GB DDR3 SDRAM memory. Equipped with a fast USB 3.1 interface. Numato Lab NLFX1002-A
zł6,539.21
3 weeks
No product available!
FPGA development board with Xilinx Kintex-7 FPGA chip with 4 GB DDR3 SDRAM memory. Equipped with a fast USB 3.1 interface. Numato Lab NLFX1002-B
zł16,029.90
3 weeks
No product available!
FPGA development board with Xilinx Kintex-7 FPGA chip with 4 GB DDR3 SDRAM memory. Equipped with a fast USB 3.1 interface. Numato Lab NLFX1002-C
zł21,242.40
3 weeks
No product available!
FPGA development board with Xilinx Spartan 6 chip. Equipped with PCIe interface and two 1Gb DDR3 SDRAM memories. Numato Lab FPGAPCIE0001A
zł2,457.75
3 weeks
No product available!
FPGA development board with Xilinx Spartan 6 chip. Equipped with PCIe interface and two 1Gb DDR3 SDRAM memories. Numato Lab FPGAPCIE0001B
zł2,975.05
3 weeks
No product available!
FPGA development board with Xilinx Spartan 6 chip. Equipped with PCIe interface and two 1Gb DDR3 SDRAM memories. Numato Lab FPGAPCIE0001C
zł4,129.66
3 weeks
No product available!
FPGA development board with Xilinx Artix-7 FPGA. Equipped with 24 GB of DDR3 SDRAM memory and an Edge Rate Rugged High-Speed male connector. Numato Lab NLFX1009
zł9,833.91
3 weeks
No product available!
FPGA development board with Spartan 6 chip and 16 Mb SPI Flash memory, 8 LEDs and buttons. Numato Lab FPGA002
zł376.97
24h
Available quantity: 2
Available
Development kit with Xilinx Artix 7 FPGA. Equipped with display, buttons, video outputs, Ethernet and microSD slot. Numato Lab NLFX1001
zł1,277.96
24h
Available quantity: 2
Available
FPGA development board with Artix 7 chip and FTDI\'s FT2232H two-channel USB converter. Numato Lab NLFX1008
zł824.80
24h
Available quantity: 1
Available
Development board FPGA with ZYNQ XC7Z020-1CLG400C system, built-in USB, audio / video interfaces, JTAG programmer and compatible connector Arduino UNO R3 and Raspberry Pi. The set works with the open-source PYNQ project that combines FPGA with Python. TUL PYNQ-Z2