Categories

Kamami.pl - Official Raspberry Pi distributor

New products



Eclypse Z7 Bundle (471-036-1) - Eclypse Z7 + 2 x Zmod ADC 1410 evaluation kit

Eclypse Z7 evaluation kit (ARM Cortex-A9 + FPGA Artix-7) with two converter Zmod ADC 1410 plugged into the SYZYGY interface connector. Digilent 471-036-1

More details

ID: 579213

779,08€ gross (23% VAT)
633,40€ net

Add to wishlist

More info

Description

Evaluation kit consisting of the Eclypse Z7 base board (ARM Cortex-A9 + FPGA Artix-7) and two Zmod ADC 1410 converters, which are plugged into the SYZYGY interface connector. It is a platform for research and rapid prototyping of test and measurement applications, including program-defined radio, ultrasound and medical devices.

The set consists of:

  • Eclypse Z7 - evaluation kit with the Zynq-7000 APSoC chip integrating the ARM Cortex-A9 based processor with the Artix-7 FPGA chip. It enables key hardware analysis and acceleration, while integrating processor, DSP and ASSP functions on one device. Eclypse Z7 is a powerful platform for prototyping. Provides two SYZYGY interface connectors enabling cooperation with fast modular systems.
  • 2 x Zmod ADC 1410 - a dual-channel ADC converter compatible with the SYZYGY standard. The module can simultaneously obtain two 25 V signals with 14-bit resolution and sampling frequency up to 100 MS/s. Zmod ADC is based on the AD9648 chip.
Attention!
The Zmod DAC 1411 module is also compatible with the Eclypse Z7 base board, which is not included in the set. If the project requires a DAC converter, it must be purchased separately or a set in a different configuration should be selected.

The set works under the control of Linux. API software is included with the pre-built Linux images. The system allows new users to start working without interfering with the hardware configuration until required. The software supports many popular programming languages, including Python and C/C++.

Manufacturer's documentation is available for the modules: Eclypse Z7Zmod ADC.

Features

Eclypse Z7

  • Zynq-7000 APSoC (XC7Z020-1CLG484C)
    • 667 MHz dual-core Cortex-A9 processor
    • DDR3L memory controller with 8 DMA channels and 4 High Performance AXI3 Slave ports
    • High-bandwidth peripheral controllers: 1G Ethernet, USB 2.0, SDIO
    • Low-bandwidth peripheral controllers: SPI, UART, CAN, I2C
    • Programmable from JTAG, Quad-SPI flash, and microSD card
    • Programmable logic equivalent to Artix-7 FPGA
  • Memory
    • 1 GiB DDR3L with 32-bit bus @ 1066 MT/s
    • 16 MB Quad-SPI Flash with factory programmed 128-bit random number and 48-bit globally unique EUI-48/64™ compatible identifier
    • microSD card slot
  • Power
    • Powered from external 12V 5A supply
    • Platform MCU for configuration of adjustable power supplies and temperature management
  • USB and Ethernet
    • Gigabit Ethernet PHY
    • USB-JTAG programming circuitry
    • USB-UART bridge
    • USB micro AB port with USB 2.0 PHY with Host/Device/OTG capabilities
  • Zmod Ports
    • 2 ports following the SYZYGY Standard interface specification
    • Compatible with a variety of SYZYGY pods, allowing for a wide variety of applications
    • Dedicated differential clocks for input and output
    • 8 differential I/Os per port
    • 16 single-ended I/Os per port
    • DNA interfaces connected to Platform MCU allowing for various auto-negotiated power supply configurations
  • Pmod Ports
    • 2 twelve-pin ports for a total of 16 FPGA-connected I/Os
    • High speed voltage translation and protection circuitry
  • User GPIO
    • 2 push-buttons
    • 2 RGB LEDs

Zmod ADC 1410

  • Channels: 2
  • Channel type: single-ended
  • Resolution: 14-bit
  • Input range: ±1V (High Gain) or ±25V (Low Gain)
  • Absolute Resolution 0.13mV (High Gain) or 3.21mV (Low Gain)
  • Sample rate (real time): 100MS/s
  • Input impedance: 1MΩ||18pF
  • Analog bandwidth: 70 MHz+ @ 3dB, 30 MHz @ 0.5dB, 20 MHZ @ 0.1dB
  • Input protected to: ±50V

Video presentation

Kit contains

  • Eclypse Z7 Development Board
  • 2 x Zmod ADC 1410 module
  • FPGA fan
  • USB A to Micro B programming cable
  • USB A to Micro A cable
  • 12V 5A power supply
  • Digilent custom packaging

Downloads

Manufacturer

Accessories