Category: STARTER KITS, PROGRAMMERS, MODULES

Development board with ST Zio and ST morpho connectors, based on the STM32H753ZI microcontroller. Thanks to the embedded STLINK-V3 programmer, it is possible to program and debug the microcontroller via USB. STMicroelectronics NUCLEO-H753ZI

Module with a button, LED diode and a white cap. DFRobot DFR0029-W

The infrared distance sensor enables the detection of objects in the range from 3 to 50cm. The sensor has a digital output, the detection threshold is adjusted by a potentiometer. DFRobot SEN0164

Development board with SAMD21 microcontroller (ARM Cortex® M0+), 22 I/O lines, 12 PWM channels, micro-USB. The module has a built-in SD connector with dedicated SPI (SPI1) interfaces that allow you to play music files. Arduino MKR Zero ABX00012

Module with relay HF152FD 16A. It allows you to control devices with a current consumption of up to 16A using a low-power signal. The module has a relay activation time of about 10ms. DFRobot DFR0251

A set of accessories for connecting the Raspberry Pi minicomputer to the Qwiic ecosystem. Includes 16x2 LCD display module, IMU 9DOF module, SHIM board and Qwiic cables. SparkFun KIT-16987

The XTS-FMC module is an extension for FPGA devices that allows access to communication channels via the SMA connector. P0401

Gravity module with a colored RGB WS2812 LED. Thanks to the controller built into the diode, you can connect the modules in series and control all with one microcontroller port. DFRobot DFR0605

NUCLEO series starter kit equipped with STM32G474RE microcontroller (512 kB Flash, Cortex-M4), with built-in programmer-debugger ST-Link-V3E, equipped with connectors compatible with Arduino.

NUCLEO series starter kit equipped with STM32G431RB microcontroller (128 kB Flash, Cortex-M4), with built-in programmer-debugger ST-Link-V3E, equipped with connectors compatible with Arduino.

Starter kit equipped with a STM32G071RBT6 microcontroller (128 kB Flash, Cortex-M0 +), with a built-in programmer-debugger ST-Link / v2-1, designed for prototyping devices with USB Type-C interface. STMicroelectronics STM32G071B-DISCO

Module with a motion sensor that uses the Doppler effect to detect moving objects using microwaves. It is powered with the voltage of 5 V and has a digital output (Gravity connector). DFRobot SEN0192

A miniature development board with ATtiny85 microcontroller, on which 6 I / O pins were derived. The module is supported by Arduino IDE. modATT85

Module with a 3-axis analog MMA7361 accelerometer. There are 3 Gravity connectors on the board (for each axis). The operating range of the sensor can be configured using a DIP switch. DFRobot DFR0143

A programming module that is an element of the programming system for microcontrollers and microprocessors, which is intended for production applications. Segger Flasher ATE Programming Module (5.18.02)

The mainboard is an element of the microcontroller and microprocessor programming system intended for production applications. Segger Flasher ATE Main Module (5.18.01)

Module with an ozone detection sensor that performs measurements in the range of up to 10 ppm with a resolution of 0.01 ppm. The module is equipped with an I2C interface. DFRobot SEN0321

A set of 37 sensors with Gravity connectors for Arduino. It includes a suite of the most popular DFRobot sensors, such as light, gas, sound, touch sensors, distance sensor and accelerometer. DFRobot KIT0150

Evaluation kit with LittleBee GW1NR9 FPGA. It offers 8640 LUTs, 6480 Flip-Flops (FF), and has a built-in 8MB (64Mb) SDRAM. The board has 8 MB Flash, FTDI for UART, 8 LEDs and a button. TEC0117-01

Module with 2 relays controlled by the I2C interface. Each relay can switch currents up to 25 A at 12 to 280 V AC. SparkFun COM-16810