Gravity: Digital 10A Relay Module is a module with 10 A 35V AC / 30 VDC relay. Thanks to the wide voltage range, the control can be used with development boards powered with either 5 V or 3.3 V or even 1.8 V. The module uses a high-quality relay HF3FD / 012-HSTF that guarantees 1 million switching cycles. The LED also has an LED to indicate the relay is on. The module has protection in the form of an insulating stand.
Attention!
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
ModRL01 module with 10A/250VAC (10A/24VDC) relay, supply of 5 V load relay coil, additional control circuit, protected overvoltage control
Your 5V system can wield great power with this big, beefy relay board. Kit contains all the parts you need to get your high-power load under control. Sparkfun KIT-13815
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
Module with 5 A 250 VAC relay. DFRobot DFR0017
Module with 32 12 V relays with a load of up to 7 A. The board communicates via the Ethernet interface. Numato Lab 32ETHRL001
No product available!
Programmable time module with relay, allows you to set the time and manner of relay reaction on the trigger signal, has a built-in LED display. It can be supplied with voltage from the range of 6 - 30VDC or using the microUSB connector
No product available!
8-channel PoE module with relays allowing you to connect your PC to other electronic circuits via the network. It does not need a separate cable for power and data transmission. It can be controlled via a simple web interface or Telnet. Numato Lab NLRP1001-A
No product available!
Module with 16 relays and 8 GPIO pins and 8 analog inputs. It communicates via the RS485, USB or Ethernet interface and supports the Modbus RTU/TCP protocol. Numato Lab NLRM1001-A
No product available!
Module with a 12 V relay and a timer. It allows you to turn the device on and off cyclically at a specified time using potentiometers. It can also operate in single trigger mode, which allows the device to be turned on after a signal has been applied for a specified period of time. The operating time can be adjusted from 1 s to 100 s or from 1 s to 15 min
Module with a 12 V relay and a timer. It enables the implementation of delayed switching on or off of the circuit with the possibility of time adjustment
No product available!
Module with MOSFET transistor, 5-36 V, 20 A, switching frequency 1 kHz. DFRobot DFR0457
Module with 8 relays with a voltage of 24 V and a load of up to 10 A. The board communicates via the Ethernet interface. Numato Lab 8ETHRL001-24
No product available!
2-channel SSR 240V / 2A relay module with fuse. modSSR-2CH
Module with 8 relays 24 V with a maximum switching current of 7 A. Communicates via the USB interface. Numato Lab RL80001-24
No product available!
Module with 2 SSR relays with a load of up to 3 A. The board is equipped with the ULN2003 system and communicates via a digital interface. Numato Lab SSRC20001-AC
The remotely controlled modulation module MOD-34 / AZ allows wireless load control with up to 10 A current consumption via a relay. It does not contain nRF24l01.
Board with the WiFi ESP-12F (ESP8266) module and a 5 V relay. Equipped with an AC adapter
Module with two 240V/2A relays controlled by 5V with a fuse triggered by a high state. modSSR-2CH-H
No product available!
Module with 8 relays and 8 IO pins and 8 analog inputs. It communicates via the RS485 or USB interface and supports the Modbus RTU protocol. Numato Lab NLRE1001-A
No product available!
Gravity: Digital 10A Relay Module is a module with 10A 35VAC / 30VDC relay compatible with devices with control signals in the range of 2.8 ... 5.5V. DFRobot DFR0473