

zł17.08 tax excl.
The module contains eight 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select high or low switching. The module is equipped with screw connectors. modRL08_ISO
The module allows independent control of eight loads connected to the output, and the optical separation of inputs from relays protects the device controlling the module against damage. modRL08_ISO operates at 5V and can control the load with the maximum current consumption of 10A (at 250V AC) in NO / NC mode. Both input and output signals are connected to the screw connectors, which guarantees an effective and reliable connection. The module also has the ability to change the state at which the relay should be activated - it can be triggered by a low or high state.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The module contains two 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select switching with high or low status. The module is equipped with screw connectors. modRL02_ISO
The module contains four 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select switching with high or low status. The module is equipped with screw connectors. modRL04_ISO
The module is equipped with eight 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. The board recommended for use with Arduino enables the control of eight relays using only two microcontroller lines. ICSTATION ICSE014A
The module contains a 5 V relay with a maximum current of 10 A (250 VAC) and optoisolated inputs, and with jumpers it is possible to select high or low switching. The module is equipped with screw connectors
Module with four 240V/2A relays controlled by 5V with a fuse triggered by a high state. modSSR-4CH-H
Module with 32 relays and 8 analog inputs. Communicates via the WiFi wireless interface. Numato Lab WFRL320001
No product available!
Module with 64 relays with a maximum switching current of 10 A. It communicates via the USB interface. Numato Lab RL640001
No product available!
The remotely controlled modulation module MOD-34 / AZ allows wireless load control with up to 10 A current consumption via a relay. It does not contain nRF24l01.
A magnetic latching relay that features low power consumption and quiet operation. It allows switching of signals up to 36 V and 10 A. It remains in the last position it was in before power was lost. DFRobot DFR0996
Module with 4 relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL40001
No product available!
8-channel module with relays, designed to work with the Raspberry Pi. It can switch 250VAC/7A or 30VDC/10A signals. SB Components 21871
Module with relay up to 5.5 A and 240 V AC controlled by the I2C interface. SparkFun COM-15093
2-channel module with relays designed to work with the Raspberry Pi Pico. It can switch signals up to 250 V AC and 7 A or 30 V DC and 10 A. SB Components 21284
Industrial module with an Ethernet interface that allows you to control 8 relays via the RJ45 port. It uses Modbus TCP protocol, supports PoE (Power over Ethernet) and is equipped with a rail-mounted housing. Waveshare Modbus POE ETH Relay
No product available!
Module with 4 SSR relays with a load of up to 3 A. The board is equipped with the ULN2003 system and communicates via a digital interface. Numato Lab SSRC40001-DC
No product available!
Module with 2 relays 12 V with a load of up to 7 A. The board communicates via the Bluetooth wireless interface. Numato Lab BTRL002
Industrial module based on the ESP32-S3 microcontroller, which supports WiFi, Bluetooth and RS485 interface. Equipped with 6 high-power relays (up to 10A at 250VAC/30VDC), it allows for safe control of various devices and integration with industrial sensors via the Modbus protocol. The module supports popular programming environments such as Arduino and MicroPython, making it ideal for AIoT and remote monitoring applications. Waveshare ESP32-S3-Relay-6CH
No product available!
Module with 32 12 V relays with a load of up to 7 A. The board communicates via the Ethernet interface. Numato Lab 32ETHRL001
No product available!
I/O module supporting Modbus RTU via USB and RS485 and Modbus TCP via Ethernet. It has 4 built-in SPST relays and 8 digital inputs, 8 digital outputs and 4 analog inputs. Provides a flexible DIN rail mounting system. Numato Lab NLRXE002-A
No product available!
The module contains eight 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select high or low switching. The module is equipped with screw connectors. modRL08_ISO