zł8.05 tax excl.
The module with two 12 V relays and optoisolation enables safe control of AC and DC loads from a microcontroller. Support for high-level or low-level triggering and LED indication make it a universal component in automation systems, control applications, and DIY projects. modRL02_ISO-12V
Relay module with two 12 V relays, designed for controlling AC and DC loads in electronic projects, automation systems, and microprocessor-based control. The circuit is equipped with optoisolation on the control inputs, which increases noise immunity and provides galvanic separation between low-voltage circuits and controlled loads. It supports triggering by either high or low logic level, with the mode selectable via configuration jumpers. Each channel has an independent control signal and a status LED indicator.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
2-channel SSR 240V / 2A relay module with fuse. modSSR-2CH
Module with 8 relays with a maximum switching current of 2 A. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP8025ADAM
The module with the relay is designed for the M5Stack sets. It allows you to control devices with a working voltage of up to 220 V AC and a current of up to 3 A or a voltage of 30 V DC and an intensity of 3 A. M5Stack U023
Module with 4 relays with a maximum switching current of 7 A. Equipped with the ATmega328P microcontroller, it can be programmed in the Arduino IDE. Numato Lab PRLY002
Module with 16 relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL160001
4-channel module with relays, designed to work with the Raspberry Pi. It can switch 120VAC/2A or 24VDC/2A signals. SB Components 14071
8-channel module with relays designed for minicomputers Raspberry Pi. It allows you to control devices powered by high voltage. Waveshare RPi Relay Board (B)
4-channel SSR 240V / 2A relay module with fuse. modSSR-4CH
Module with 8 SSR relays with a load of up to 3 A. The board communicates via the Ethernet interface. Numato Lab 8ETHSSR001-AC
No product available!
No product available!
Module with 64 relays and 8 GPIO pins and 6 analog inputs. It communicates via the RS485, USB or Ethernet interface and supports the Modbus RTU/TCP protocol. Numato Lab NLRM1003-A
No product available!
Universal module supervised by the website, which can control both DC circuits as well as powered from 230 V mains. The states of digital inputs, relays and control buttons are presented on the website. AVTMOD05
Module with 4 digital inputs, 4 outputs and 6 analog (current) inputs. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP9038ADAM
The module is equipped with eight 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. The board recommended for use with Arduino enables the control of eight relays using only two microcontroller lines. ICSTATION ICSE014A
Industrial Ethernet module that allows control of 30 relays via RJ45 port. It uses Modbus TCP protocol, PoE (Power over Ethernet) power supply and comes with a rail-mounted housing. Waveshare Modbus POE ETH Relay 30CH
No product available!
Module with 4 relays JZC-11F with a load of 5A. It enables switching devices with high power using a microcontroller. I2C communication. SparkFun COM-16566
The module with two 12 V relays and optoisolation enables safe control of AC and DC loads from a microcontroller. Support for high-level or low-level triggering and LED indication make it a universal component in automation systems, control applications, and DIY projects. modRL02_ISO-12V