Relay module with optocoupler 10A/250V, 5V coil, low triggered
ID: 1193816
5906623497201
zł6.90
Tax included
zł5.61 tax excl.
The 5V relay module with opto-isolation allows you to safely control loads up to 10A at voltages up to 250V AC or 30V DC, working with microcontroller platforms such as Arduino or Raspberry Pi
Description
The module equipped with the JQC-3FF-S-Z relay allows you to control electrical devices that draw up to 10 A at a voltage of up to 250 V AC or 30 V DC. Thanks to the applied opto-isolation (EL817), the control signal is galvanically separated from the executive part, which increases the safety of the control system. The module can be controlled by platforms such as Arduino, Raspberry Pi or STM32.
The module's leads have a standard 2.54 mm pitch, which makes it easy to connect using connecting cables. Mounting holes with a diameter of 3 mm allow for convenient attachment of the module to the substrate.
The system is switched on with a low state - applying a LOW signal to the IN input causes the relay to switch. The relay contacts are marked as:
- NO (Normally Open) - disconnected by default
- NC (Normally Closed) - connected to COM by default
- COM (Common) - common lead
Depending on the load used, the module has a power consumption of 0.36 W to 0.51 W. It can operate at temperatures from -25°C to +70°C and at humidity from 45% to 85%.
Features
- VCC supply voltage: 5 V
- JQC-3FF-S-Z relay
- Switched on low state
- EL817 optoisolation
- Contact parameters for resistive load:
- 125 V AC / 10 A
- 250 V AC / 10 A
- 30 V DC / 10 A
- 28 V DC / 10 A
- Board dimensions: 53 x 28 mm
- Mounting hole diameter: 3 mm
1193816
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
Module with 32 relays and 8 GPIO pins and 8 analog inputs. It communicates via the RS485, USB or Ethernet interface and supports the Modbus RTU/TCP protocol. Numato Lab NLRM1002-A
zł3,146.18
3 weeks
No product available!
Module with 16 relays and 8 GPIO pins and 8 analog inputs. It communicates via the RS485, USB or Ethernet interface and supports the Modbus RTU/TCP protocol. Numato Lab NLRM1001-A
zł2,752.78
3 weeks
No product available!
Module with electromechanical relay. It allows you to control devices with an operating voltage of up to 250 V AC and a current of up to 3 A or a voltage of 30 V DC and a current of 3 A
zł9.27
24h
Available quantity: 8
Available
Industrial module with 8 relays. It communicates via RS485 interface and supports Modbus RTU protocol. Waveshare Modbus RTU Relay (EN)
zł123.50
24h
Available quantity: 12
Available
Module with 4 digital inputs, 4 outputs and 6 analog (current) inputs. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP9038ADAM
zł232.45
4 weeks
No product available!
Module with 8 relays with a maximum switching current of 2 A. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP8025ADAM
zł218.34
4 weeks
No product available!
Module with 8 digital inputs and 4 relays with a maximum switching current of 2 A. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP8024ADAM
zł222.81
24h
Available quantity: 3
Available
AO3406 MOSFET transistor module with N channel and JST PH2.0 connector designed to control motor, solenoid or LEDs. Adafruit 5648
zł20.93
4 weeks
No product available!
Module with eight 240V/2A relays controlled by 5V with a fuse triggered by a low state. modSSR-8CH-L
zł50.04
24h
Available quantity: 1
Available
Module with one 240V/2A relay controlled by 5V with a fuse triggered by a high state. modSSR-1CH-H
zł6.73
24h
Available quantity: 1
Available
Module with two 240V/2A relays controlled by 5V with a fuse triggered by a high state. modSSR-2CH-H
zł13.15
4 weeks
No product available!
Module with four 240V/2A relays controlled by 5V with a fuse triggered by a high state. modSSR-4CH-H
zł23.03
4 weeks
No product available!
Module with eight 240V/2A relays controlled by 5V with a fuse triggered by a high state. modSSR-8CH-H
zł53.65
4 weeks
No product available!
A magnetic latching relay that features low power consumption and quiet operation. It allows switching of signals up to 36 V and 10 A. It remains in the last position it was in before power was lost. DFRobot DFR0996
zł33.25
24h
Available quantity: 1
Available
4-channel switch module with a maximum voltage of 16 V and a current of 2 A based on a MOSFET transistor. It is controlled by digital inputs. It is equipped with a screw connection and status LEDs. Adafruit 5757
zł62.87
4 weeks
No product available!
Industrial module with 16 relays. It communicates via the RS485 interface and supports the Modbus RTU protocol. Waveshare Modbus RTU Relay 16CH
zł178.94
24h
Available quantity: 22
Available
The 5V relay module with opto-isolation allows you to safely control loads up to 10A at voltages up to 250V AC or 30V DC, working with microcontroller platforms such as Arduino or Raspberry Pi