modRL02_ISO - power module with two 5V relays and optoisolation of inputs
ID: 559500
5906623454884
zł8.54
Tax included
zł6.94 tax excl.
The module contains two 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select switching with high or low status. The module is equipped with screw connectors. modRL02_ISO
Description
The module allows independent control of two loads connected to the output, and the optical separation of inputs from relays protects the device controlling the module against damage. modRL02_ISO operates at 5V and can control the load with the maximum current consumption of 10A (at 250V AC) in NO / NC mode. Both input and output signals are connected to the screw connectors, which guarantees an effective and reliable connection. The module also has the ability to change the state at which the relay should be activated - it can be triggered by a low or high state.
properties
- Module with two relays
- Input optoisolation
- Operating voltage: 5 V DC
- Power consumption: approx. 80 mA / channel
- It has LEDs for channel operation and module power supply
- The possibility of independent configuration of the triggering state
- Screw connectors for input and output signals
- NO and NC contacts are output
- It has mounting holes with a diameter of 3 mm
- Dimensions: 41 x 50 x 20 mm
559500
Data sheet
- Output current
- 10A
- Number of channels
- 2
- Executive element
- Przekaźnik
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The module contains four 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select switching with high or low status. The module is equipped with screw connectors. modRL04_ISO
zł22.40
24h
Available quantity: 4
Available
The module contains eight 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select high or low switching. The module is equipped with screw connectors. modRL08_ISO
zł21.01
24h
Available quantity: 20
Available
The module contains a 5 V relay with a maximum current of 10 A (250 VAC) and optoisolated inputs, and with jumpers it is possible to select high or low switching. The module is equipped with screw connectors
zł8.84
24h
Available quantity: 226
Available
Other products in the same category (16)
Extension module compatible with Raspberry Pi. The board is equipped with three 24 V 2 A relays, three buffer inputs, three sink outputs and three analog inputs with a working range up to 24 V. Pimoroni PIM213
zł183.33
24h
Available quantity: 3
Available
Module with 64 relays with a maximum switching current of 10 A. It communicates via the USB interface. Numato Lab RL640001
zł2,654.43
3 weeks
No product available!
Module with 2 SSR relays with a load of up to 3 A. The board communicates via the USB interface. Numato Lab SSR20001-DC
zł421.93
3 weeks
No product available!
The module with the relay is designed for the M5Stack sets. It allows you to control devices with a working voltage of up to 220 V AC and a current of up to 3 A or a voltage of 30 V DC and an intensity of 3 A. M5Stack U023
zł21.21
24h
Available quantity: 2
Available
Module with 2 relays 12 V with a load of up to 7 A. The board communicates via the Bluetooth wireless interface. Numato Lab BTRL002
zł356.15
24h
Available quantity: 1
Available
The module with 4 relays, designed to work with the micro:bit. It allows you to control devices with operating parameters up to 120VAC/2A or 24VDC/2A. SB Components 14118
zł84.48
24h
Available quantity: 1
Available
8-channel module with relays, designed to work with the Raspberry Pi. It can switch 250VAC/7A or 30VDC/10A signals. SB Components 21871
zł107.87
24h
Available quantity: 3
Available
The module is equipped with eight 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. The board recommended for use with Arduino enables the control of eight relays using only two microcontroller lines. ICSTATION ICSE014A
zł50.41
24h
Available quantity: 5
Available
Module with 4 relays JZC-11F with a load of 5A. It enables switching devices with high power using a microcontroller. I2C communication. SparkFun COM-16566
zł170.59
24h
Available quantity: 1
Available
Module with eight 240V/2A relays controlled by 5V with a fuse triggered by a low state. modSSR-8CH-L
zł50.04
24h
Available quantity: 10
Available
Module with 32 24 V relays with a load of up to 7 A. The board communicates via the Ethernet interface. Numato Lab 32ETHRL001-24
zł1,375.89
3 weeks
No product available!
Module with 16 12 V relays with a load of up to 7 A. The board communicates via the Ethernet interface. Numato Lab 16ETHRL001
zł744.33
24h
Available quantity: 3
Available
AO3406 MOSFET transistor module with N channel and JST PH2.0 connector designed to control motor, solenoid or LEDs. Adafruit 5648
zł20.77
24h
Available quantity: 2
Available
Module with 4 relays with a maximum switching current of 7 A. Equipped with the ATmega328P microcontroller, it can be programmed in the Arduino IDE. Numato Lab PRLY002
zł437.79
24h
Available quantity: 1
Available
This SPST solid-state relay module allows for safe switching of DC circuits up to 60 V and 7 A, offering galvanic isolation and low conduction resistance (approx. 30 mΩ) thanks to the use of back-to-back MOSFET transistors. It features fast switching time (up to 1 ms), low control current consumption (approx. 10 mA), and the ability to control a signal from 2.7 to 40 V. Its compact design, lack of mechanical components, and the ability to mount on 2.54 mm connectors or screw terminals make the module a durable and quiet solution for systems requiring reliable isolation and long service life. Pololu 5420
zł15.14
4 weeks
No product available!
Module with 4 SSR relays with a load of up to 3 A. The board communicates via the USB interface. Numato Lab SSR40001-AC
zł559.60
3 weeks
No product available!
The module contains two 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select switching with high or low status. The module is equipped with screw connectors. modRL02_ISO