![Remotely controlled executive module with relay Remotely controlled executive module with relay](https://kamami.pl/23154-large_default/mod-34-a-z-remotely-controlled-executive-module-with-relay.jpg)
![Remotely controlled executive module with relay Remotely controlled executive module with relay](https://kamami.pl/23154-large_default/mod-34-a-z-remotely-controlled-executive-module-with-relay.jpg)
zł42.23 tax excl.
The remotely controlled modulation module MOD-34 / AZ allows wireless load control with up to 10 A current consumption via a relay. It does not contain nRF24l01.
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
Remotely controlled executive module with relay (without module nRF24L01)
Description
The module enables remote switching on and off of systems operating with voltage or current other than that used by the control system.
For example, when we want to connect an LED strip powered with +12 V to a microcontroller, we can not do it directly, due to the microcontroller operating voltage limitation. Then an executive module acting as a switch should be used. The module must be powered via a USB connector or via a pin connector. The output connectors of the relay are connected to the power supply circuit, just like a normal mechanical switch, using 2 out of 3 available pins, middle and extreme. Depending on which of the extreme pins we choose, the module will short-circuit or open the circuit, i.e. switch the controlled system on or off.
The set does not contain the radio module nRF24L01.
Technical data:
Set contains:
To download
The module is equipped with eight 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. The board recommended for use with Arduino enables the control of eight relays using only two microcontroller lines. ICSTATION ICSE014A
2-channel SSR 240V / 2A relay module with fuse. modSSR-2CH
AO3406 MOSFET transistor module with N channel and JST PH2.0 connector designed to control motor, solenoid or LEDs. Adafruit 5648
Module with electromechanical relay. It allows you to control devices with an operating voltage of up to 250 V AC and a current of up to 3 A or a voltage of 30 V DC and a current of 3 A
Module with 8 relays with a voltage of 24 V and a load of up to 10 A. The board communicates via the Ethernet interface. Numato Lab 8ETHRL001-24
No product available!
Module with 4 SSR relays with a load of up to 3 A. The board is equipped with the ULN2003 system and communicates via a digital interface. Numato Lab SSRC40001-AC
No product available!
Module with eight 240V/2A relays controlled by 5V with a fuse triggered by a low state. modSSR-8CH-L
Module with 8 relays and 8 IO pins and 8 analog inputs. It communicates via the RS485 or USB interface and supports the Modbus RTU protocol. Numato Lab NLRE1001-A
No product available!
Module with 32 24 V relays with a load of up to 7 A. The board communicates via the Ethernet interface. Numato Lab 32ETHRL001-24
No product available!
Module with 16 relays with a maximum switching current of 7 A. It communicates via a USB interface. Numato Lab RL160001-24
No product available!
The module contains eight 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select high or low switching. The module is equipped with screw connectors. modRL08_ISO
No product available!
Module with 8 relays and 10 analog inputs. Communicates via the WiFi wireless interface. Numato Lab WFRL80001
No product available!
Module with 4 relays controlled by the I2C interface. Each relay can switch currents up to 40 A at 28-380 V AC. SparkFun KIT-16833
8-channel module with relays designed to work with the Raspberry Pi Pico. Has built-in power isolation. Perfect for industrial applications. Waveshare Pico-Relay-B
8-channel module with relays designed for minicomputers Raspberry Pi. It allows you to control devices powered by high voltage. Waveshare RPi Relay Board (B)
Module with MOSFET and a Gravity connector. It allows you to easily connect and control the voltage from 5V to 30V and the current up to 2.5A. DFRobot DFR0643
The remotely controlled modulation module MOD-34 / AZ allows wireless load control with up to 10 A current consumption via a relay. It does not contain nRF24l01.