SparkFun Beefcake Relay Control Kit (Ver. 2.0)
ID: 562057
5906623417643
zł52.71
Tax included
zł42.85 tax excl.
Your 5V system can wield great power with this big, beefy relay board. Kit contains all the parts you need to get your high-power load under control. Sparkfun KIT-13815
Description
Your 5V system can wield great power with this big, beefy relay board. How does 10A on the NC contacts and 20A on the NO contacts at 220VAC sound? The SparkFun Beefcake Relay Control Kit contains all the parts you need to get your high-power load under control. Only minimal assembly is required!
The heart of the board is a sealed, SPDT 20A/10A Relay. The relay is controlled by 5V logic through a transistor, and an LED tells you when the relay is closed. This is a kit, so it comes as through-hole parts with assembly required, which makes for some nice soldering practice. Screw terminal connectors on either side of the board make it easy to incorporate into your project.
There are some pretty beefy traces connecting the relay to the load pins, but the 3-pin terminals are only rated for 15A max! If you plan on connecting a larger load, you’ll need to solder directly to the board. As always with high current and voltage, play it safe and use your judgment when deciding how much of a load you want to put on a board – in open airflow the PCB can handle the full 20A for a few minutes at a time, but in an enclosed area heat can build up.
Note: Please keep in mind that this board is really meant for someone with experience and good knowledge of electricity. If you’re uncomfortable soldering or dealing with high voltage, please check out the PowerSwitch Tail II. The PowerSwitch Tail II is fully enclosed, making it a lot safer.
Features
- Voltage Rating: 220VAC/28VDC
- VCC requirements: 4-6V, 150mA capable
- SPDT pins exposed (Form C)
- 14 AWG screw terminals for relay connections.
- 10 AWG solder lugs for relay connections.
- Flyback diode included
- Zener recovery diode included (decreases turn-off time)
- Heavy 2 oz. copper on PCB
562057
Data sheet
- Output current
- 10A
- Number of channels
- 1
- Executive element
- Przekaźnik
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Available
Board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface
zł54.89
Delivery date unknown
No product available!
Development board with ATmega32u4 microcontroller (AVR), 20 I / O lines, 7 PWM channels, 16 MHz quartz, micro-USB. Easy-to-use USB support libraries, sensors, displays, etc. are available. A000052
zł119.29
24h
Available quantity: 3
Available
Other products in the same category (16)
Module with 4 SSR relays with a load of up to 3 A. The board communicates via the USB interface. Numato Lab SSR40001-AC
zł559.60
3 weeks
No product available!
8-channel module with relays, designed to work with the Raspberry Pi. It can switch 250VAC/7A or 30VDC/10A signals. With LCD 4,3" display. SB Components 21871
zł421.32
24h
Available quantity: 2
Available
8 Channel Ethernet Solid State Relay Module - module with 8 SSR AC relays and Ethernet communication
Module with 8 SSR relays with a load of up to 3 A. The board communicates via the Ethernet interface. Numato Lab 8ETHSSR001-AC
zł1,031.69
3 weeks
No product available!
Module with SSR 240V/2A relay controlled by 5V voltage with fuse. modSSR-1CH
zł8.43
24h
Available quantity: 30
Available
Industrial module with 16 relays. It communicates via the RS485 interface and supports the Modbus RTU protocol. Waveshare Modbus RTU Relay 16CH
zł185.94
24h
Available quantity: 8
Available
The module contains a 5 V relay with a maximum current of 10 A (250 VAC) and optoisolated inputs, and with jumpers it is possible to select high or low switching. The module is equipped with screw connectors
zł8.84
24h
Available quantity: 301
Available
Module with 32 24 V relays with a load of up to 7 A. The board communicates via the Ethernet interface. Numato Lab 32ETHRL001-24
zł1,375.89
3 weeks
No product available!
Module with a 12 V relay and a timer. It allows you to turn the device on and off cyclically at a specified time using potentiometers. It can also operate in single trigger mode, which allows the device to be turned on after a signal has been applied for a specified period of time. The operating time can be adjusted from 1 s to 100 s or from 1 s to 15 min
zł14.55
24h
Available quantity: 17
Available
Compact module with MOSFET IRF520 24V/5A transistor.
zł3.26
24h
Available quantity: 51
Available
The module with two 12 V relays and optoisolation enables safe control of AC and DC loads from a microcontroller. Support for high-level or low-level triggering and LED indication make it a universal component in automation systems, control applications, and DIY projects. modRL02_ISO-12V
zł9.90
4 weeks
No product available!
2-channel SSR 240V / 2A relay module with fuse. modSSR-2CH
zł34.50
24h
Available quantity: 6
Available
Module with a 12 V relay and a timer. It enables the implementation of delayed switching on or off of the circuit with the possibility of time adjustment
zł44.90
4 weeks
No product available!
Module with 2 5 V relays with a maximum switching current of 2 A. It communicates via the USB interface and does not require an additional power supply. Numato Lab USBPOWRL001
zł177.35
24h
Available quantity: 4
Available
Industrial module with 8 relays and 8 digital inputs. It communicates via the RS485 interface and supports communication using the Modbus RTU protocol. Waveshare Modbus RTU Relay (D)
zł137.94
4 weeks
No product available!
8-channel PoE module with relays allowing you to connect your PC to other electronic circuits via the network. It does not need a separate cable for power and data transmission. It can be controlled via a simple web interface or Telnet. Numato Lab NLRP1001-A
zł1,359.00
3 weeks
No product available!
Module with 4 relays with a maximum switching current of 7 A. Equipped with the ATmega328P microcontroller, it can be programmed in the Arduino IDE. Numato Lab PRLY002
zł437.79
24h
Available quantity: 1
Available
Your 5V system can wield great power with this big, beefy relay board. Kit contains all the parts you need to get your high-power load under control. Sparkfun KIT-13815