2 Channel Programmable Relay Module - programmable module with 2 relays
ID: 1180927
5906623411467
zł325.54
Tax included
zł264.67 tax excl.
Module with 2 relays with a maximum switching current of 7 A. Equipped with the ATmega328P microcontroller, it can be programmed in the Arduino IDE. Numato Lab PRLY001
Description
Module with 2 relays 12 V and built-in ATmega328P microcontroller. It allows you to switch devices with high power and current up to 7 A. It can be programmed using the Arduino IDE, making it a much more flexible solution than other available modules with relays. All relay terminals (C, NC, NO) are available on screw terminals, which makes it very easy to connect the board. The module is equipped with digital inputs / outputs, analog inputs, real time clock (RTC) and Micro SD memory card slot. Perfect for automation systems that require the control of multiple devices. Full documentation is available on the product page.
Features
- ATmega328P microcontroller with 32 KB of flash memory
- Compatible with the Arduino IDE
- Converter USB-UART FT232RL
- 2 SPDT 12V mechanical relays
- 4 digital inputs/outputs
- 2 PWM outputs
- 4 analog inputs
- I2C interface
- Real time clock (RTC)
- Battery backup for the real time clock
- Micro SD card slot
- LED indicators for power, TX, RX and relays
- ISP for programming or updating the bootloader
- 16 MHz quartz
- USB mini connector
- Dimensions: 100 x 60 mm
1180927
Data sheet
- Output current
- 7 A
- Number of channels
- 2
- Executive element
- Przekaźnik
- Coil voltage
- 12 VDC
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Module with 2 SSR relays with a load of up to 3 A. The board is equipped with the ULN2003 system and communicates via a digital interface. Numato Lab SSRC20001-DC
zł323.98
24h
Available quantity: 1
Available
Module with 2 5 V relays with a maximum switching current of 2 A. It communicates via the USB interface and does not require an additional power supply. Numato Lab USBPOWRL001
zł166.12
24h
Available quantity: 4
Available
Module with 2 SSR relays with a load of up to 3 A. The board is equipped with the ULN2003 system and communicates via a digital interface. Numato Lab SSRC20001-AC
zł325.54
24h
Available quantity: 1
Available
Module with 2 relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL20001
zł171.11
24h
Available quantity: 1
Available
Module with 4 relays with a maximum switching current of 7 A. Equipped with the ATmega328P microcontroller, it can be programmed in the Arduino IDE. Numato Lab PRLY002
zł437.79
24h
Available quantity: 1
Available
Other products in the same category (16)
Compact module with MOSFET IRF520 24V/5A transistor.
zł3.08
24h
Available quantity: 45
Available
Module with 5V relay and timer. It allows the implementation of delayed switching on or off of the circuit with adjustable time in the range from 1 s to 100 s and from 1 s to 15 min.
zł13.62
4 weeks
No product available!
Module with a 12 V relay and a timer. It allows you to turn the device on and off cyclically at a specified time using potentiometers. It can also operate in single trigger mode, which allows the device to be turned on after a signal has been applied for a specified period of time. The operating time can be adjusted from 1 s to 100 s or from 1 s to 15 min
zł14.55
4 weeks
No product available!
Module with 24V relay and timer. It allows the implementation of delayed switching on or off of the circuit with adjustable time in the range from 1 s to 100 s and from 1 s to 15 min.
zł13.60
24h
Available quantity: 2
Available
12V relay module with a radio receiver in a set with a remote control operating at 433 MHz.
zł34.08
4 weeks
No product available!
Module with MOSFET and a Gravity connector. It allows you to easily connect and control the voltage from 5V to 30V and the current up to 2.5A. DFRobot DFR0643
zł37.86
24h
Available quantity: 1
Available
Module with 4 relays JZC-11F with a load of 5A. It enables switching devices with high power using a microcontroller. I2C communication. SparkFun COM-16566
zł170.59
24h
Available quantity: 1
Available
Module with relay HF152FD 16A. It allows you to control devices with a current consumption of up to 16A using a low-power signal. The module has a relay activation time of about 10ms. DFRobot DFR0251
zł47.32
4 weeks
No product available!
Module with 2 relays controlled by the I2C interface. Each relay can switch currents up to 25 A at 12 to 280 V AC. SparkFun COM-16810
zł901.07
3 weeks
No product available!
Module with a relay and WiFi communication. Compatible with ESP-01 or ESP-01S
zł9.32
24h
Available quantity: 6
Available
Module with SSR M281 relay with a load of up to 1 A. The board is equipped with a Grove connector and is controlled by a digital input. Seeed Studio 101020603
zł29.75
24h
Available quantity: 3
Available
Module with 4 relays SRD-05VDC-SL-C with a load up to 10 A. The board was equipped with a Grove connector and communicates via I2C. Seeed Studio 103020133
zł67.35
24h
Available quantity: 3
Available
Module with 2 relays SRD-05VDC-SL-C with a load up to 10 A. The board is equipped with a Grove connector and is controlled by a digital signal. Seeed Studio 103020132
zł46.59
24h
Available quantity: 1
Available
Module with 8 relays SSR G3MC202P with a load up to 2 A. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 103020136
zł446.91
4 weeks
No product available!
Module with 2 relays SSR G3MC202P with a load up to 2 A. The board is equipped with a Grove connector and is controlled via digital inputs. Seeed Studio 103020134
zł188.52
24h
Available quantity: 2
Available
Module with relay SSR G3MC202P with a load up to 2 A. The board is equipped with a Grove connector and is controlled via digital input. Seeed Studio 103020137
zł87.59
4 weeks
No product available!
Module with 2 relays with a maximum switching current of 7 A. Equipped with the ATmega328P microcontroller, it can be programmed in the Arduino IDE. Numato Lab PRLY001