 
        
           
        
           
         
           
           
           
          Module with 8 relays with a voltage of 12 V and a load of up to 10 A and 10 GPIO pins that can work in the analog input mode. It allows the switching of high-power devices over the Ethernet interface and is controlled by the built-in, easy-to-use network interface or any popular terminal emulator that supports the TELNET protocol. Each module is shipped with a unique MAC address. These devices also support assigning and retrieving custom identification strings that can be used to distinguish individual devices when a large number of boards are connected to the same network. All outputs are available on screw terminals, which makes it easy to connect external devices. The module will be used in home automation projects, lighting systems and garden equipment. Full documentation is available on the product page.

Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Module with 64 relays with a maximum switching current of 10 A. It communicates via the USB interface. Numato Lab RL640001
 No product available!
8-channel IO expander with 6 analog inputs. Communicates via the Bluetooth wireless interface. Numato Lab BTIO001X
Module with 8 relays with a voltage of 12 V and a load of up to 7 A. The board communicates via the Bluetooth wireless interface. Numato Lab BTRL001
 No product available!
Module with 8 relays with a voltage of 24 V and a load of up to 10 A. The board communicates via the Ethernet interface. Numato Lab 8ETHRL001-24
 No product available!
2-channel module with relays, designed to work with the Raspberry Pi. It can switch 250VAC/7A or 30VDC/10A signals. SB Components 14088
Industrial module with an Ethernet interface that allows you to control 8 relays via the RJ45 port. It uses Modbus TCP protocol, supports PoE (Power over Ethernet) and is equipped with a rail-mounted housing. Waveshare Modbus POE ETH Relay
 No product available!
Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 3191
ModRL01 module with 10A/250VAC (10A/24VDC) relay, supply of 5 V load relay coil, additional control circuit, protected overvoltage control
Module with 5 A 250 VAC relay. DFRobot DFR0017
A versatile module that allows you to control higher voltage devices such as 12V LED strips while simultaneously powering a microcontroller from 3.3V. The module integrates an LMR14203 converter and an N-channel MOSFET (PSMN7R0-100BS), allowing you to power the board at up to 12V and drive loads up to 10A, with additional protection features and LED indicators, making it ideal for projects requiring efficient power control. SparkFun COM-23979
Module with 16 relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL160001
Module with 2 relays 12 V with a maximum switching current of 7 A. Numato Lab RL20002
Module with eight 240V/2A relays controlled by 5V with a fuse triggered by a low state. modSSR-8CH-L
Module with SSR 240V/2A relay controlled by 5V voltage with fuse. modSSR-1CH
Module with 4 5 V relays with a maximum switching current of 2 A. It communicates via the USB interface and does not require an additional power supply. Numato Lab USBPOWRL004
The module with the TPL5110 timer, which can generate a signal with an adjustable period from 100 ms to 2 h. It also works well as an external Watchdog Timer. Adafruit 3435
Module with a 12 V relay and a timer. It allows you to turn the device on and off cyclically at a specified time using potentiometers. It can also operate in single trigger mode, which allows the device to be turned on after a signal has been applied for a specified period of time. The operating time can be adjusted from 1 s to 100 s or from 1 s to 15 min
Industrial module with 32 relays. It uses communication via the RS485 interface and supports the Modbus RTU protocol. Waveshare Modbus RTU Relay 32CH
4-channel switch module with a maximum voltage of 16 V and a current of 2 A based on a MOSFET transistor. It is controlled by digital inputs. It is equipped with a screw connection and status LEDs. Adafruit 5757
 
                    Module with 8 relays with a voltage of 12 V and a load of up to 10 A. The board communicates via the Ethernet interface. Numato Lab 8ETHRL001