The module with 16 relays with a control voltage of 24 V and a load of up to 7 A and 8 GPIO pins that can work in the analog input mode. It enables the switching of high-power devices over Ethernet. For control, the user can use an easy-to-use interface launched in the browser or any terminal emulator supporting the TELNET protocol. Each module is shipped with a unique MAC address. These devices also support assigning and retrieving custom identification strings that can be used to distinguish individual devices when a large number of boards are connected to the same network. All outputs are available on screw terminals, which makes it easy to connect external devices. The module will be used in home automation projects, lighting systems and garden equipment. Full documentation is available on the product page.

Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Module with 16 12 V relays with a load of up to 7 A. The board communicates via the Ethernet interface. Numato Lab 16ETHRL001
Module with 32 12 V relays with a load of up to 7 A. The board communicates via the Ethernet interface. Numato Lab 32ETHRL001
No product available!
Module with 32 24 V relays with a load of up to 7 A. The board communicates via the Ethernet interface. Numato Lab 32ETHRL001-24
No product available!
Module with 8 relays with a voltage of 12 V and a load of up to 10 A. The board communicates via the Ethernet interface. Numato Lab 8ETHRL001
Module with 8 relays with a voltage of 24 V and a load of up to 10 A. The board communicates via the Ethernet interface. Numato Lab 8ETHRL001-24
No product available!
The module is equipped with four 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. ICSTATION ICSE012A
2-channel module with relays, designed to work with the Raspberry Pi. It can switch 250VAC/7A or 30VDC/10A signals. SB Components 14088
Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 3191
Module with relay HF152FD 16A. It allows you to control devices with a current consumption of up to 16A using a low-power signal. The module has a relay activation time of about 10ms. DFRobot DFR0251
No product available!
Module with 16 relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL160001
Module with 4 relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL40001
No product available!
Module with 8 relays with a voltage of 12 V and a load of up to 10 A. The board communicates via the Ethernet interface. Numato Lab 8ETHRL001
Module with eight 240V/2A relays controlled by 5V with a fuse triggered by a low state. modSSR-8CH-L
Module with 4 digital inputs, 4 outputs and 6 analog (current) inputs. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP9038ADAM
The 5 V relay module enables safe switching of high-voltage loads via microcontroller logic. Its compact size, mechanical durability, and wide operating conditions make it a versatile choice for automation, lighting control, and DIY electronics projects.
8-channel PoE module with relays allowing you to connect your PC to other electronic circuits via the network. It does not need a separate cable for power and data transmission. It can be controlled via a simple web interface or Telnet. Numato Lab NLRP1001-A
No product available!
Module with 32 12 V relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL320001
Module with a 12 V relay and a timer. It allows you to turn the device on and off cyclically at a specified time using potentiometers. It can also operate in single trigger mode, which allows the device to be turned on after a signal has been applied for a specified period of time. The operating time can be adjusted from 1 s to 100 s or from 1 s to 15 min
4-channel module with relays, designed to work with the Raspberry Pi. It can switch 120VAC/2A or 24VDC/2A signals. SB Components 14071
Module with 2 relays controlled by the I2C interface. Each relay can switch currents up to 25 A at 12 to 280 V AC. SparkFun COM-16810
No product available!
Module with 8 relays with a voltage of 12 V and a load of up to 7 A. The board communicates via the Bluetooth wireless interface. Numato Lab BTRL001
No product available!
Module with 16 24 V relays with a load of up to 7 A. The board communicates via the Ethernet interface. Numato Lab 16ETHRL001-24