Category: STARTER KITS, PROGRAMMERS, MODULES

Set with OpenLog Artemis data logger. The set includes an I2C expander, a strain gauge module, a USB type C cable, a 1250 mAh LiPo battery, a 1 GB microSD card and all the necessary Qwiic cables. SparkFun KIT-18295

An expansion board that enables the implementation of TCPP01-M12 functions and USB Type C surge protection for VBUS and CC lines suitable for sink applications. STMicroelectronics X-NUCLEO-SNK1M1

The RX FINE adapter converts a standard 20-pin 2.54 mm connector to a 14-pin 2.54 mm connector. It enables the connection of Segger programmers with RX devices from Renesas. Segger RX Fine Adapter (8.06.10)

An adapter that converts a standard 20-pin 2.54 mm connector to a 10-pin 2.54 mm connector. It enables the connection of Segger programmers with Silicon Labs devices and development boards with a C2 interface. Segger SiLabs C2 Adapter (8.06.17)

The USB-UART converter is designed to work with the MicroMod Asset Tracker board. It facilitates direct communication with the SARA-R510M8S u-blox module. SparkFun DEV-17725

Adapter that converts standard 20-pin 2.54 mm connector to SWIM connector and 10-pin connector. Used for programming STM8 chips. Segger STM8 Adapter (8.06.22)

SiFive-ARTY adapter for debugging between J-Link and the ARTY board with SiFive RISC-V. Segger SiFive-ARTY Adapter (8.06.24)

AVR PDI adapter from standard 2.54mm 20 pin connector to 2.54mm 6 pin, 1.27mm 6 pin or 2.54mm 10 pin AVR PDI connector. Segger AVR PDI Adapter (8.06.26)

Adapter from the standard 20-pin 2.54 mm connector to the 10-pin 1.27 mm connector often used in Cortex-M boards. Segger 50-Mil 10-Pin Patch Adapter (8.06.28)

Power adapter providing a stabilized 5V supply voltage for the target board. Segger 5V Target Supply Adapter (8.06.29)

Adapter providing two dedicated supply voltages - for programming and powering for the target board. Useful for programming modules that do not support low voltage programming or require a voltage other than 5V. Segger Programming Voltage Adapter (8.06.30)

An adapter to connect the JTAG to a target hardware system that has an automotive connector. It has a 20 pin 2.54mm JTAG connector and a 19 pin 1.27mm Samtec FTSH connector. Segger Infineon AUTO-20 Adapter (8.06.33)

A small module with a PIR motion sensor. It allows detecting movement within a maximum range of 6 meters (default up to 3 meters). The measuring angle is 120 degrees. The module has a connector in accordance with the Grove standard. Seeed Studio 101020020

Grove module with a small vibration motor. Seeed studio 105020003

Development kit with RP2040 microcontroller equipped with two ARM Cortex-M0 + cores that work at 133 MHz, 264 kB RAM. The board has a QVGA camera, LCD display, IMU system and a microphone. ArduCAM B0302

An expansion board designed for MicroMod main modules. Equipped with the LTE-M / NB-IoT u-blox SARA-R510M8S module. It allows you to monitor devices remotely. SparkFun DEV-17272

STM32F723E-DISCO Discovery kit allows users to develop applications with the microcontrollers of the STM32F7 Series, based on ARM®Cortex®-M7 core. The PMOD, STMod+ and Arduino™Uno V3 connectivity support provides unlimited expansion capabilities with a large choice of specialized add-on boards.

Tomasz Frenchman

Gravity I2C OLED-2864 Display is an OLED display with I2C interface with 128x64 resolution, powered by 3.3-5V. DFRobot DFR0486

LIDAR distance sensor with a measuring range from 5 cm to 10 m and a resolution of 1 cm. It communicates via the I2C or ANT interface. The set includes a module with Qwiic SparkFun SEN-18009 connectors