Category: STARTER KITS, PROGRAMMERS, MODULES

Robert Wołgajew

Universal minicomputer with STM32F103C6 microcontroller (ARM Cortex-M3 @72 MHz, 32 kB Flash, 10 kB RAM, LQFP48 package)

Expander (overlay) extending the functionality of the STM32 Nucleo development board. Shield has ST Morpho connectors and is equipped with in a four-segment 7-segment display, four RGB diodes, LIS35DE accelerometer, LPS25HB pressure sensor, and DS18B20 digital thermometer

Kamod BluePill+ is a modern development board with STM32F103 microcontroller, equipped with SPI, I2C, UART interfaces, two 12-bit ADC converters and USB-C connector, ideal for creating projects based on ARM Cortex-M3 architecture

Development kit with nRF52840 microcontroller with ARM Cortex M4F core and BLE communication. Equipped with motion sensors and a microphone. Seeed Studio 102010469

Programmable RGB and RGBA LED driver

Demo and programming kit for NFC tags. Designed for emulation using the NTAG I²C plus tag system in embedded systems. NXP NTAG I2C Plus Explorer Kit

KAmodRPi-GPRS-GPS is an overlay for Raspberry Pi 4 / 3B + / 3B / 2B / B + computers, which allows you to enrich the system with the ability to send data via GPRS, SMS transmission or work as a module for Bluetooth communication. This extension also offers the ability to receive satellite data from location systems - GPS and GLONASS.

Evaluation kit equipped with equivalent of STM32F103C8T6 microcontroller (ARM Cortex M3, 72MHz, 64kB Flash, 20kB SRAM). It has two 20-pin connectors enabling the use of numerous microcontroller peripheral systems

Development kit with STM32L496ZGT6 microcontroller (ARM Cortex-M4 core) with a built-in ST-Link programmer. Extensive equipment, including: MEMS 6DoF sensor, motor controller, joystick, LED display, 8 LED diodes, RGB LED, audio amplifier, Flash memory QSPI 1 MB, microphone, Arduino connector

RJ12 6-Pin PH 10-Pin IDC Adapter for PIC Microcontrollers Programming

The KAmod BlackPill 401 is an evaluation board with an STM32F401CCU microcontroller, featuring USB-C with ESD protection and a modified power circuit. With a pre-installed bootloader, it supports Arduino IDE, offering 32 GPIOs and versatile programming capabilities

Development board D1 Mini with WiFi module ESP-8266MOD and 4 MB Flash memory. The module can be programmed from the Arduino IDE level. WeMos D1 Mini

Multifunctional board for STM32 NUCLEO, built based on operational amplifiers. Has, among others built-in LED current controller, prototype area and window discriminator

Evaluation board for STM32F103 microcontrollers

A LoRa communication module based on the Semtech SX1262 chip, supporting the 862–930 MHz band. It enables reliable, long-range data transmission with minimal power consumption, making it ideal for IoT projects and battery-powered systems. The module offers up to 22 dBm transmit power, low power consumption in sleep mode, and full compatibility with Seeed Studio XIAO boards. Seeed Studio 113010003

Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.

The module is based on the ESP8266EX chip. Thanks to the support of the 802.11 b/g/n standard, it enables wireless communication with WiFi networks, which allows for Internet access and data exchange. It is programmed via the USB Type-C connector using Arduino, MicroPython or NodeMCU. WeMos D1 Mini Type-C

STM32 Nucleo-64 development board with STM32F446RET6 MCU, supports Arduino and ST morpho connectivity

The board with the RP2040 microcontroller equipped with two ARM Cortex-M0 + cores, which work at a frequency of 133 MHz, 264 kB RAM. The board also has 2 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Seeed Studio 102010428