Category: STARTER KITS, PROGRAMMERS, MODULES

Development kit with STM32L496ZGT6 microcontroller with built-in ST-Link programmer. Extensive equipment, including: MEMS 6DoF sensor, motor controller, joystick, LED display, 8 LED diodes, RGB LED, audio amplifier, Flash memory QSPI 1 MB, microphone.

A small DIP adapter with a 2.54 mm goldpin connector. Designed for the ESP-01 and ESP-01S modules

Compact development board based on ESP32-C5 with dual-band WiFi6 2.4GHz and 5GHz, Bluetooth 5 LE, and IEEE 802.15.4, equipped with factory-soldered pin headers, designed for advanced low-power IoT projects. XIAO ESP32-C5 (Pre-Soldered)

KAmodRPI RS485 CAN HAT is a shield for the Raspberry Pi computer that extends its interfaces with RS485 and CAN. Bus signals are led out to goldpin connectors and terminal blocks.

Base board for dipPLD modules with XC2C256 (CoolRunner-II by Xilinx)

WiFi module based on ESP8266. The module has a built-in antenna and USB-UART converter. The module can be programmed in Lua (under the control of the NodeMCU firmware) or in the Arduino environment. 10 GPIO lines are available which each can be configured to work as PWM, I2C.

Starter kit with micro:bit v2. In addition to the micro:bit v2 board, the set includes a microUSB-USB cable, a battery basket and two AAA batteries. SparkFun DEV-17288

A compact IoT board with a 160 MHz RISC-V processor, offering support for Wi-Fi 6, Bluetooth 5, Zigbee 3.0, Thread 1.3 and Matter. With a built-in lithium battery charger and voltage monitoring function, it is ideal for mobile and energy-saving applications. The board can act as both an end device and a network gateway, making it extremely versatile in modern smart home systems. DFRobot DFR1117

Development board with the NXP iMXRT1062 microcontroller based on the ARM Cortex-M7 core. It can be programmed using any environment and C language or using the Arduino IDE. PJRC TEENSY40_PINS

Pressure-Sensitive Conductive Sheet. Adafruit 1361

JTAG interface for microcontrollers with ARM core

Real time clock (RTC) module PCF8523. It uses the STEMMA QT connector and communicates via the I2C interface. Adafruit 5189

LoLin NodeMCU V3 is a board with ESP8266 (ESP12E). The ESP8266 system provides WiFi connectivity (802.11 b / g / n). The USB-UART converter (CH340G chip) is located on the board. The module can be programmed in Lua (under the control of the NodeMCU firmware) or in the Arduino environment. There are 10 GPIO lines available.

The KAmod ESP32-C3 board, equipped with a RISC-V microcontroller and a set of MEMS and SHTC3 sensors, enables the creation of IoT, measurement, and control applications. Thanks to power from USB-C or a battery and support for Arduino and Rust, it works perfectly in mobile projects and embedded systems.

STM32 Nucleo-64 development board with STM32L476RGT6 MCU, supports Arduino and ST morpho connectivity

Marcin. Bonds

Development board D1 Mini V3 with WiFi module ESP-8266 and 4 MB Flash memory. The module can be programmed from the Arduino IDE level. WeMos D1 Mini V3.x

Espressif ESP32-S3 WiFi module board with 32-bit dual-core Xtensa 32-bit LX7 processor. It offers 4 MB Flash memory and 512 kB SRAM and an RGB LED. It has a built-in ceramic WiFi/BLE antenna. Waveshare ESP32-S3-Zero

WiFi module developed by AI-Thinker Co., Ltd with ESP8266 processor. Integrates a 32-bit MCU microcontroller with 80 MHz clock, RTOS support, Wi-Fi and antenna. The module supports the IEEE802.11 b / g / ni standard and has a complete TCP / IP protocol stack. AI-Thinker ESP-12S

Board with RP2040 microcontroller and W5100S network chip. The module is equipped with an Ethernet connector. WIZnet W5100S-EVB-Pico