A set with the TIMI-MB module equipped with a 0.96" TFT LCD display with a resolution of 160x80 px, controlled by the PIXXI-28 controller and Mates Programmer. SparkFun DEV-19254

The module is equipped with an RGB 65K display with a resolution of 160x80 pixels and a diagonal of 0.96 inches, which is controlled directly by the PIXXI-28 graphics processor from 4D Labs. It has pins compatible with the prototype board and has been designed to work with development modules equipped with a mikroBUS™ Click socket. SparkFun LCD-19253

A set with a TIMI-96 module equipped with a 0.96" TFT LCD display with a resolution of 160x80 px, controlled by a PIXXI-28 controller and a Mates Programmer. SparkFun DEV-19252

GPS module with built-in antenna. It can provide location, speed and accurate time information using standard NMEA-0183 protocol. SparkFun GPS-19166

Surface loudspeaker with an impedance of 4 Ω and a power output of 10 W. It is constructed with a coil attached to a pad that conducts vibrations. SparkFun COM-19102

A powerful 3D AI+CV platform that provides complete and ready-to-use hardware-accelerated machine vision. It uses three cameras (IMX214 and two OV7251) and a USB 3.0 port. SparkFun SEN-19040

A set of cameras designed for projects related to artificial intelligence in the IoT area. The module contains three built-in cameras (two 720P and one 12MP) configured using the USB 3.0 interface via the type C connector and the ESP32 module for communication via WiFi or Bluetooth. SparkFun SEN-18737

A compact 9-DOF sensor that combines a 3-axis accelerometer, magnetometer, and gyroscope to precisely determine an object\'s orientation. With support for the I2C/SPI bus, compatibility with the STEMMA QT system, and 3V/5V power supply, it is suitable for robotics, 3D navigation, VR, AR, and stabilization systems. Adafruit 4634

Module with CO2, temperature and humidity sensor SCD-40. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5187

Module with 4-digit 7-segment LED display. The board is equipped with a TM1637 driver and communicates via a digital interface

High-quality conductive thread that allows easy sewing by hand or machine, making it an ideal choice for e-textile projects. Coated with a nano-layer of silver, the thread has low resistance that stabilizes after sewing, and its conductivity is uniform along its entire length, eliminating the risk of non-conductive sections. Additionally, the thread is durable, does not fray and can be used in standard sewing machines, making it practical and easy to use. Kitronik 2722

Module with 4-digit 7-segment LED display. The board is equipped with a TM1637 driver and communicates via a digital interface

Female terminal block, angled, 10-pin. Pitch 5.0mm. Height 15mm. 2EDGK-5.0-10P

Module with 4-digit 7-segment LED display. The board is equipped with a TM1637 driver and communicates via a digital interface

5V relay module with IR receiver. Comes with a remote control

Female terminal block, 3-pin. Pitch 5.0mm. Height 15mm. Suitable for 2EDGRC male strips with a pitch of 5.0 mm. 2EDGKN-5.00

A module with a light sensor in the form of a photoresistor. There is a comparator and a potentiometer on the board. The module has a digital output

Adapter with 3.3V voltage regulator designed for NRF24L01 modules with 8-pin connector

STM32H753VIT6, 32-bit microcontroller, Arm Cortex-M7 with 2 MB Flash, 1 MB RAM, 480 MHz, DSP with DP-FPU, HW Crypto, LQFP100

RC extension cable dedicated to servos, comes with JR/Futaba female and male connectors. It has twisted wires