Category: Extension modules for Raspberry Pi

Module with 17x7 LED matrix display (119 LEDs) designed to work with the Raspberry Pi. It uses the IS31FL3731 driver and communicates via the I2C interface. Pimoroni PIM491

Module with e-Paper display, 2.7" diagonal and 264x176 px resolution. Communication via SPI interface. Waveshare 2.7inch e-Paper HAT

Extension module compatible with Raspberry Pi. The board is equipped with three 24 V 2 A relays, three buffer inputs, three sink outputs and three analog inputs with a working range up to 24 V. Pimoroni PIM213

A pin expander designed to work with the Raspberry Pi. It provides 2 UART and 8 GPIO interfaces and communicates via the I2C bus. SB Components 14873

Extension module with a driver for two stepper motors based on the HR8825 system. Dedicated for Raspberry Pi minicomputers. Waveshare Stepper Motor HAT (B)

Board with the NB-IoT SIM7028 module intended for Raspberry Pi. It communicates via the UART interface and AT commands. Waveshare SIM7028-NB-IoT HAT (EN)

IPS 3.5" LCD display with touch screen. The display is equipped with a DPI interface for image display and I2C interface for a touch panel. Resolution 640x480 pixels. Waveshare 3.5inch DPI LCD

A 3-port HUB module with a USB 3.2 Gen1 interface with an RJ45 connector designed to work with the Raspberry Pi minicomputer. Waveshare USB 3.2 Gen1 HUB Gigabit ETH HAT

Module with environmental sensors for Raspberry Pi. It allows you to measure temperature, humidity, pressure, illuminance, detection of VOC, IR and UV radiation and orientation. Waveshare Environment Sensor HAT

Expansion module designed to work with a portable computer built into the Raspberry Pi 400 keyboard. There are two 40-pin connectors on the board in a vertical position. SB Components 21307

Expansion board with LoRaWAN SX1302 and GNSS L76B dedicated to the Raspberry Pi. The kit includes the 868M antenna, GPS and cables. Waveshare SX1302 868M LoRaWAN Gateway HAT

3.5" LCD TFT display with touch screen. The display is equipped with an SPI interface for image display and touch screen operation. Resolution 480x320 pixels. Waveshare 3.5inch RPi LCD (C)

Shield with Qwiic connectors designed for Raspberry Pi minicomputers. It allows you to easily connect the minicomputer with the Qwiic sensor system. SparkFun DEV-15945

Expansion board with LoRa E22-900T22S module for Raspberry Pi. It supports the LoRaWAN protocol and allows communication in the 868 MHz frequency band. SB Components 22571

Expansion board with LoRa Node SX1262 module and GNSS L76K dedicated for Raspberry Pi. It supports the LoRaWAN protocol and allows communication in the 868 MHz frequency band and enables positioning within the GPS, GLONASS, BDS and QZSS systems. Waveshare SX1262 868/915M LoRaWAN/GNSS HAT

Module with real-time clock and CR1225 battery socket for voltage backup. It communicates via the I2C interface. Seeed Studio 103030277

A kit consisting of an M.2 HAT+ module and a Hailo-8L accelerator with a performance of 13 TOPS enables the rapid development of advanced real-time AI applications on the Raspberry Pi 5. This setup allows neural networks for object detection and segmentation to run on the Hailo-8L coprocessor, leaving the Raspberry Pi 5 CPU available for other tasks. The foundation has also prepared rpicam-apps libraries that significantly facilitate the creation of AI projects. Raspberry Pi SC1438

Module with barcode and QR scanner designed for Raspberry Pi. It allows you to read one-dimensional and two-dimensional codes using the intelligent image recognition algorithm. SB Components 22595

HAT module designed for the Raspberry Pi minicomputer. It allows you to add an RS485 interface and a CAN bus to the project, allowing for wired communication of many devices over long distances. SB Components 21444