Category: Main categories

Universal expansion board with screw connectors dedicated to the Raspberry Pi. Facilitates prototyping

Yellow plastic cap for the monostable button (Tact Switch). Fits switches with dimensions 12x12x7.3 mm

LCD TFT 5" display with touch screen. The display is equipped with an HDMI interface and USB for touch screen. Resolution 800x480 pixels. Waveshare 5inch HDMI LCD (H) V4

Tape, in the form of a braid, for removing excess melted solder when soldering and desoldering electronic components, 1.5 m

RS485 - Ethernet converter that provides easy communication between the RS485 and RJ45 Ethernet interface. Configurable via website or AT commands. Waveshare RS485 TO ETH (for EU)

The Yato YT-0842 upholstery clip remover, 200 mm in length, is designed for the safe removal of upholstery clips in vehicles. Made from chrome-plated carbon steel, it features a non-slip PVC handle for a secure grip during use. Its forked tip allows for easy extraction of upholstery fasteners without the risk of damaging them. Yato YT-0842

STM32G473CET6, Arm Cortex-M4 microcontroller with DSP and FPU, 170MHz with 512 Kbytes of Flash memory, LQFP48

RC extension cable dedicated to servos, comes with JR/Futaba female and male connectors

Kinetis L Series Cortex-M0+, 32bit MCU, 32kB Flash, QFN24, Freescale, RoHS

The ZCG PG21-18J PA66 cable gland is a high-quality component made from durable polyamide (PA66) in a light gray color, designed for sealing cables with an outer diameter of 13 to 18 mm. Equipped with a PG21 thread, it provides effective protection for cables against mechanical damage and external factors, making it an ideal solution for a variety of electrical and electronic applications.

Plastic enclosure Z47 lightgray ABS

Universal control module designed for 3D printers. It is based on the STM32G0B1 microcontroller, but can use a Raspberry Pi CM4 or CB1 minicomputer as the main module. It has a built-in interface for connecting displays, LED strips and temperature sensors. BIGTREETECH Manta M5P

Female terminal block, 5-pin. Pitch 3.81mm. Height 7.8mm. Suitable for 15EDGRC male strips with a pitch of 3.81 mm. 2EDGKN-3.81

Brass Prusa Nozzle with a 0.4mm diameter designed for Original Prusa 3D printers with the Nextruder hotend

Pulse generator module based on the NE555 system with frequency control using a potentiometer. It is powered with the voltage ranging from 5 V to 12 V

PoE adapter for Raspberry Pi 5 that provides direct power over Ethernet, compliant with IEEE 802.3af/at standards. It features a metal heatsink and a powerful fan to efficiently dissipate heat, and supports PCI-E×1 Gen2 and Gen3 modes, enabling fast data transfer on M.2 drives of various sizes. Additionally, the adapter offers 5V at 4.5A output on GPIO and 12V at 2A on the 2-pin connector, allowing you to power additional devices, making it ideal for IoT and networking applications that require reliability. Waveshare POE M.2 HAT+

Pulley GT2 36T B5 for a shaft with a diameter of 5 mm. It has 36 teeth, suitable for a 10mm wide belt

Module with the MAX31865 amplifier dedicated to PT100 and PT1000 temperature probes in 2, 3 or 4-wire versions. It uses the SPI bus and the EZ interface connector. BIGTREETECH EZ31865

Permanent cylindrical neodymium magnet with a diameter of 2 mm and a height of 2 mm. Set of 10 pcs

The 2.4-inch LCD display module is a compact screen that offers the ability to conveniently display information in small devices. The module is dedicated to 3D printers and offers the ability to connect to main boards via the FPC tape or the EXP1+EXP2 interface. BIGTREETECH MINI12864 V2.0