- Out-of-Stock
 
        
           
         
           
           
          The Teensy is a breadboard-friendly development board with loads of features in a, well, teensy package. Each Teensy 3.2 comes pre-flashed with a bootloader so you can program it using the on-board USB connection: No external programmer needed! PJRC TEENSY32
The Teensy is a breadboard-friendly development board with loads of features in a, well, teensy package. Each Teensy 3.2 comes pre-flashed with a bootloader so you can program it using the on-board USB connection: No external programmer needed! You can program for the Teensy in your favorite program editor using C or you can install the Teensyduino add-on for the Arduino IDE and write Arduino sketches for Teensy!
The processor on the Teensy also has access to the USB and can emulate any kind of USB device you need it to be, making it great for USB-MIDI and other HID projects. The 32 bit processor brings a few other features to the table as well, such as multiple channels of Direct Memory Access, several high-resolution ADCs and even an I2S digital audio interface! There are also 4 separate interval timers plus a delay timer! Oh yeah, and all pins have interrupt capability. Also, it can provide system voltage of 3.3V to other devices at up to 100mA.
All of this functionality is jammed into a 1.4 x 0.7 inch board with all headers on a 0.1" grid so you can slap in on a breadboard and get to work! The Teensy 3.2 adds a more powerful 3.3 volt regulator, with the ability to directly power an ESP8266 Wifi, WIZ820io Ethernet, and other 3.3V add-on boards that require a little more power. Additionally, if it is used within the Teensy 3.1 limits of operation, the Teensy 3.2 and 3.1 are interchangeable!
Note: This does not come with a USB cable, please check below for an appropriate one.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Pin header goldpin black 1x40 pins. Straight connector for through-hole assembly. 2.54mm pitch.
Teensy Prop Shield is meant for making light and sound effects on small, handheld props and wearable costumes. This shield features a 2W audio amp, high-speed 5V buffers for driving APA102 LEDs, and an 8MB flash memory. PJRC PROP-SHIELD-LC
 No product available!
 No product available!
The UGEARS tractor is a rattling greeting from centuries past. No electronics - just plywood, a rubber band motor, and tons of fun! UGears 70003
 No product available!
The module with the ACS725 current sensor with a direct current measuring range up to 10 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020616
 No product available!
Detection device (eg in the wall) metal and wire with current (URZ1204)
 No product available!
 No product available!
 No product available!
 No product available!
 No product available!
 No product available!
 No product available!
 No product available!
Starter kit with LOGO! 8 230RCE, software and necessary accessories. Siemens 6ED1057-3BA03-0AA8
 No product available!
Set of 4 mounting plates for Raspberry Pi 4B compatible with 19-inch 3U rack mount. The holder shown in the 3rd picture is not included in the set and must be purchased separately. ArduCAM U6131
 No product available!
 No product available!
RoboClaw 2x60AHV Motor Controller (V7C) is a two-channel DC motor driver, operating voltage: 10,5 to 60V, maximum continuous current: 60A, the ability to easily implement feedback loops with PID controller, security systems. Pololu 3583
 No product available!
 
                    The Teensy is a breadboard-friendly development board with loads of features in a, well, teensy package. Each Teensy 3.2 comes pre-flashed with a bootloader so you can program it using the on-board USB connection: No external programmer needed! PJRC TEENSY32