- Out-of-Stock
The Teensy is a breadboard-friendly development board with loads of features in a, well, teensy package. Each Teensy 3.2 comes pre-flashed with a bootloader so you can program it using the on-board USB connection: No external programmer needed! PJRC TEENSY32
The Teensy is a breadboard-friendly development board with loads of features in a, well, teensy package. Each Teensy 3.2 comes pre-flashed with a bootloader so you can program it using the on-board USB connection: No external programmer needed! You can program for the Teensy in your favorite program editor using C or you can install the Teensyduino add-on for the Arduino IDE and write Arduino sketches for Teensy!
The processor on the Teensy also has access to the USB and can emulate any kind of USB device you need it to be, making it great for USB-MIDI and other HID projects. The 32 bit processor brings a few other features to the table as well, such as multiple channels of Direct Memory Access, several high-resolution ADCs and even an I2S digital audio interface! There are also 4 separate interval timers plus a delay timer! Oh yeah, and all pins have interrupt capability. Also, it can provide system voltage of 3.3V to other devices at up to 100mA.
All of this functionality is jammed into a 1.4 x 0.7 inch board with all headers on a 0.1" grid so you can slap in on a breadboard and get to work! The Teensy 3.2 adds a more powerful 3.3 volt regulator, with the ability to directly power an ESP8266 Wifi, WIZ820io Ethernet, and other 3.3V add-on boards that require a little more power. Additionally, if it is used within the Teensy 3.1 limits of operation, the Teensy 3.2 and 3.1 are interchangeable!
Note: This does not come with a USB cable, please check below for an appropriate one.
Data sheet
Manufacturer
Responsible person
Arducam Nano RPI Module is a minicomputer equipped with Broadcom BCM2835 processor and VideoCore IV GPU. The module has two CSI connectors for connecting cameras, video output (PAL), SPI, I2C, UART, and GPIO. ArduCam B0101
No product available!
Evaluation set designed for the use of Internet of Things based on ArduCAM-Mini-2MP and ArduCAM-ESP8266-Nano-V2 modules. ArduCAM-Mini-2MP is a module with a 2 megapixel camera with an OV2640 transducer and an ESP8266 chip. Mounting the M12 lens. ArduCAM B0085
No product available!
3.5 "TFT display with touch panel, transparent housing and 16 GB SD card for Raspberry Pi 3. ArduCAM U470302
No product available!
Display with a touch screen (resistive panel) with a diagonal of 3.5 inches and a resolution of 480 x 320 pixels. Uses the SPI interface. Intended for use with the Raspberry Pi Zero / B + / 2/3 minicomputer. ArduCAM U470301
No product available!
A set of basic electronic components complete with contact plate, connecting cables and Mega2560 R3. It is ideal for beginner electronics who also know Arduino. ArduCAM KB0003
No product available!
A set of basic electronic components complete with contact plate, connecting cables and board compatible with Arduino UNO R3. It is ideal for beginner electronics who also know Arduino. Uctronics KB0002
No product available!
A set of basic electronic components complete with contact plate, connecting cables and Arduino UNO R3. It is ideal for beginner electronics who also know Arduino. ArduCAM KB0001
No product available!
Orange filament 1.75 mm 0.85 kg Easy PLA by Fiberlogy
No product available!
No product available!
No product available!
12 pin GPIO ribbon cable (200mm) for Odroid XU4 and Odroid XU4Q
No product available!
7 pin GPIO ribbon cable (20 cm) for Odroid C4
No product available!
No product available!
3-wire cable with JST-ZH plug, 30 cm, 3x1 JST, 1.5 mm pitch
No product available!
A set for building a four-wheel, remote-controlled vehicle. Equipped with a programmable Arduino Uno R3 controller and set of sensors. modARD_02
No product available!
No product available!
The Teensy is a breadboard-friendly development board with loads of features in a, well, teensy package. Each Teensy 3.2 comes pre-flashed with a bootloader so you can program it using the on-board USB connection: No external programmer needed! PJRC TEENSY32