- Out-of-Stock
Four-wheel remote-controlled robot with Arduino Uno R3 (assembly kit)
ID: 568506
A set for building a four-wheel, remote-controlled vehicle. Equipped with a programmable Arduino Uno R3 controller and set of sensors. modARD_02
Description
A set for assembly a construction of a four-wheeled vehicle based on a 4WD chassis. Equipped with a programmable Arduino Uno R3 controller and a remote controller. Each wheel has a separate motor connected to the L298N controller. The set includes an ultrasonic sensor on the servo mechanism, contrast sensors, IR receiver and Bluetooth module HC-06.
The set is a great way to start having fun with robotics. It allows you to quickly and easily build a four-wheeled robot and expand its capabilities according to your needs thanks to the programmable controller!
Kit contains
- 4 x Gear motor
- 4 x Tire
- 2 x Plastic plate 100 x 213 x 5 mm
- L298N motor driver board
- Arduino Uno R3
- Expansion board for sensors
- Handle
- SG90 servo
- Ultrasonic sensor module
- 3 x TCRT5000 sensor module
- IR receiver
- Remote
- 18650 battery basket
- 18650 battery charger
- Bluetooth module HC-06
- Connection cable tapey 40 pin
- USB cable
- Screw set
568506
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.57
24h
Available quantity: 150
Available
Bluetooth module v2.0 + EDR, controlled by AT + commands with built-in antenna.
zł29.18
24h
Available quantity: 10
Available
4WD car chassis construction kit. It can be used as a base for building a robot
zł30.93
Delivery date unknown
No product available!
Other products in the same category (16)
The module with the DS18B20 sensor is used to measure the temperature in the range from -55° C to + 125° C, with an accuracy of +/- 0.5° C in the range from -10° C to + 85° C. The module communicates via the 1-Wire interface, thanks to which it can be connected using 2 or 3 wires - depending on the configuration. Temperature measurement can be performed with an accuracy of 9 to 12 bits. MOD-31.Z
Retired
No product available!
Universal module with LM358 operational amplifier. Depending on the additional elements installed, the amplifier can be freely configured, eg as a reversing, non-inverting amplifier, voltage follower or an integrating amplifier. MOD-32.Z
Retired
No product available!
No product available!
The modally controlled modulation module MOD-34 / BZ allows wireless load control with a current consumption of up to 10A via a relay. Includes wireless module nRF24l01.
Retired
No product available!
No product available!
No product available!
No product available!
The module with the TXB0108 system enables the connection of systems operating with different voltage levels. It has 8-channels and is 2-way. The transmission direction of each channel is detected automatically. MOD-38.Z
Retired
No product available!
No product available!
The STM32 eXploreM0 module contains a 32-bit microcontroller with ARM Cortex M0 core, STM32F051C8T6 (64 kB Flash memory, 8 kB RAM, 48 MHz, HDMI-CEC, I2C, IrDA, LIN, SPI, UART / USART). The USB / UART converter allows programming of the microcontroller via a USB cable. MOD-40.Z
Retired
No product available!
The STM32 eXploreM0 + module contains a 32-bit microcontroller with ARM Cortex M0 + core, STM32L051C8T6 (64 kB of Flash memory, 8 kB RAM, 32 MHz, I2C, IrDA, SPI, UART / USART). The built-in USB / UART converter enables programming of the microcontroller via a USB cable. MOD-41.Z
Retired
No product available!
No product available!
The RGB LED ruler has 8 programmable LEDs WS2812B with a built-in control system. It is possible to set a specific color for each diode. The module has an IN input for controlling and an OUT output to which further light points or other modules from WS2812B can be connected. The supply voltage is from 3.5 to 5.3 V, and the input voltage +/- 0.5 V of the supply voltage
Retired
No product available!
No product available!
No product available!
Real-time clock with PCF8563 chip and battery backup. Modally MOD-48.Z
Retired
No product available!
A set for building a four-wheel, remote-controlled vehicle. Equipped with a programmable Arduino Uno R3 controller and set of sensors. modARD_02