CAN Pal - module with CAN transceiver TJA1051T/3
ID: 1184871
5906623431632
zł20.90
Tax included
zł16.99 tax excl.
CAN transceiver module based on the TJA1051T/3 chip. Allows you to connect a board with native CAN support (the transceiver will convert 3V signals into differential CAN signals) to a network of devices. Adafruit 5708
Description
CAN transceiver module based on the TJA1051T/3 chip. Allows you to connect a board with native CAN support (the transceiver will convert 3V signals into differential CAN signals) to your device network.
CAN Bus is a networking standard, originally designed for cars. It is now widely used for robots or sensor networks that need better coverage and addressing than I2C, and do not have the pins or computational capability to communicate over Ethernet. CAN is a differential 2-wire interface, which means it allows data transmission over long distances in noisy conditions. Each CAN device sends messages whenever it wants, and with data encoding, message collisions can be detected and sent later.
The converter will find use in projects requiring stable communication with multiple devices over longer distances. Full documentation and example programmes are available on the product page.
Features
- Full compliance with ISO 11898-2:2003
- Guarantee of correct transmission times for speeds up to 5 Mbit/s in the fast CAN FD phase
- Suitable for 12 V and 24 V systems
- Low electromagnetic emission (EME) and high electromagnetic immunity (EMI)
- VIO input on TJA1051T/3 and TJA1051TK/3 allows direct connection to 3 V to 5 V microcontrollers
- Transceiver disconnects from the bus when not powered
- High resistance to electrostatic discharge (ESD)
- Bus pins protected against transients
- Undervoltage detection on VCC and VIO pins
- Thermal protection
- Screw connector for CAN network connection
- Switch for disconnection of two 60 Ohm resistors (connected in series)
- Product dimensions: 20.3 x 20.2 x 4.0mm
Kit contains
- CAN Pal module
- 3-pin screw connector
- 8-pin goldpin connector
1184871
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
CAN controller module for Feather boards. It features an MCP2515 CAN controller and a TJA1051 transceiver and allows data transfer at speeds of up to 1Mb/s. Adafruit 5709
zł66.67
24h
Available quantity: 3
Available
Other products in the same category (16)
The CAN-BUS Arduino Shield v2.0 can be stacked on an Arduino UNO, Arduino Leonardo or Arduino MEGA board. The shield integrates an MCP2515 CAN-BUS chip on the shield and has a CAN-BUS transceiver function. With an on-board DB9 and CAN-BUS connector you can choose a suitable port according to your host device. There is also an integrated MicroSD socket for data storage. DFR0370
zł94.77
24h
Available quantity: 4
Available
CAN module based on the SN65HVD230 system, allows you to connect a microcontroller with a CAN bus interface
zł17.91
4 weeks
No product available!
RS485 CAN HAT is an extension designed for the Raspberry Pi mini-computer in the form of a HAT overlay. Adds RS485 and CAN interfaces for the Raspberry Pi plate. Interface signals are derived as screw and goldpin connectors. RS485 CAN HAT
zł43.90
24h
Available quantity: 16
Available
USB - LIN bus converter module. It allows you to connect devices to your computer via the LIN bus. LIN USB CONVERTER (LUC)
zł106.91
24h
Available quantity: 37
Available
UART-CAN converter module based on the TJA1050 transceiver system. It allows for communication, for example, of a microcontroller via the CAN bus
zł4.24
4 weeks
No product available!
The CAN transmitter and receiver module is intended for M5Stack sets. It is based on an isolated CA-IS3050G transceiver system, which can provide differential data reception and transmission. M5Stack U085
zł65.57
24h
Available quantity: 3
Available
A set of necessary tools needed to perform vehicle diagnostics. It consists of a CAN Bus module, an OBD II connector and the necessary wires. Seeed Studio 114991438
zł100.76
4 weeks
No product available!
KAmodRPI RS485 CAN HAT is a shield for the Raspberry Pi computer that extends its interfaces with RS485 and CAN. Bus signals are led out to goldpin connectors and terminal blocks.
zł39.90
24h
Available quantity: 82
Available
TTL/CAN-USB converter dedicated to distance sensors TF03, TF02 and TFmini with TTL/CAN interface. Comes with a miniUSB cable. Benewake TTL/CAN to USB converter
zł199.90
4 weeks
No product available!
I2C-CAN converter using the MCP2551 and MCP2515 systems and the ATmega168PA microcontroller. The module uses the I2C bus and the Grove connector for communication. Seeed Studio 113020111
zł97.10
24h
Available quantity: 4
Available
USB-CAN adapter with support for CAN2.0A and CAN2.0B standards. It can work with Windows and Linux systems, including Raspberry Pi and Jetson Nano minicomputers. Waveshare USB-CAN-A
zł87.50
24h
Available quantity: 22
Available
CAN transceiver module based on the TJA1051T/3 chip. Allows you to connect a board with native CAN support (the transceiver will convert 3V signals into differential CAN signals) to a network of devices. Adafruit 5708
zł20.90
24h
Available quantity: 4
Available
Expansion module designed for Raspberry Pi or BIGTREETECH CB1. It allows you to add a CAN interface and use minicomputers for control in industrial or automotive applications. BIGTREETECH IO2CAN V1.0
zł49.90
24h
Available quantity: 5
Available
Communication module with CAN-UART converter and USB 1.0 interface. It supports CAN 2.0 protocol and supports SLCAN. It is operated using AT commands. DFRobot TEL0150
zł97.51
4 weeks
No product available!
Converter with a built-in microcontroller (MCU) and a CAN transceiver system. It can work with devices with an operating voltage of 3.3 V via goldpin connectors with a pitch of 2.54 mm. The converter facilitates the design and prototyping of devices based on the CAN bus. Waveshare WS-TTL-CAN
zł42.72
4 weeks
No product available!
KAmod CAN-TXRX is a CAN bus transceiver with the MCP2542FD system, compatible with the CAN 2.0 and CAN FD standards, enabling sending and reading data with the serial interface voltage level adjustable in the range of 1.7...5 V, equipped with protections and LEDs signaling action
zł37.90
24h
Available quantity: 50
Available
CAN transceiver module based on the TJA1051T/3 chip. Allows you to connect a board with native CAN support (the transceiver will convert 3V signals into differential CAN signals) to a network of devices. Adafruit 5708