Module with a DC motor driver based on the MC33886 chip. The IC has built-in internal control logic and low RDS (ON) MOSFET output circuits. It allows you to control the movement of drives with a working voltage from 5 to 28 V and a current up to 5 A. The error status output informs about too low voltage, short circuit and over temperature. It will be used in motor control projects, including robotics.
Data sheet
Manufacturer
Responsible person
Raspberry Pi Expansion Board, DC Motor / Stepper Motor Driver
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
This compact breakout board for Maxim’s MAX14870 motor driver offers a wide operating voltage range of 4.5 V to 36 V and can deliver a continuous 1.7 A (2.5 A peak) to a single brushed DC motor. It features a simple two-pin speed/direction interface and built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature.
Two-channel DC motor driver based on the HR9933 circuit. It allows you to control the movement of drives with a supply voltage of up to 10 V and power consumption up to 1.5 A. DFRobot DRI0040
Single-channel DC motor driver that can control the movement of the drive with a supply voltage of up to 36 V and a current consumption of up to 15 A. Controlled by a PWM signal. DFRobot DRI0042
Ultra small Dual DC motor driver for some room limited projects. UVLO (Under Voltage Latch-Out) features a safe guard for your system. DRI0041
No product available!
Two-channel DC motor driver communicating via UART, SPI or I2C interface. It can control the movement of 3 to 11V motors with a maximum continuous current of 1.2A per channel. SparkFun ROB-13911
No product available!
Raspberry Pi Expansion Board, DC Motor / Stepper Motor Driver
KAmodMPC17C724 is a module with a double MP bridge bridge type MPC17C724. The system allows you to control two DC brush motors or one bipolar stepping motor. The controller operates at a voltage range of 2.7 - 5.5 V and can work with motors with power consumption up to 0.4 A.
The X-NUCLEO-IHM12A1 is a low voltage dual brush DC motor driver expansion board based on the STSPIN240 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys
The high power motor driver module works on the basis of Infineon BTS7960B systems. Maximum controller current: 43 A, operating voltage range: 5.5V - 27V. The module has a heat sink and can be controlled from the Arduino, Raspberry Pi, and STM levels. IBT_2
No product available!
This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 36 Voperating range and are efficient enough to deliver a continuous 14 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation.
HAT module with a driver for two DC motors designed for Raspberry Pi. Motors can be powered with the voltage from 6.5 to 30 V and draw a maximum current of up to 18 A. Pololu 3751
No product available!
This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 Voperating range and are efficient enough to deliver a continuous 18 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation.
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 V operating range and are efficient enough to deliver a continuous 18 A without a heat sink.
No product available!
Pololu Dual G2 High-Power Motor Driver 18v22 is an extension that allows you to control two DC motors designed for Arduino tiles. The motor can be supplied with 6.5 ... 30V voltage and can draw up a maximum current of 22A. Polol 2517
No product available!
Pololu Dual G2 High-Power Motor Driver 24v18 is an extension that allows you to control two DC motors designed for Raspberry Pi. The motors can be supplied with 6.5-36V voltage and can draw a maximum current of 18A. Pololu 3756
No product available!
Module with a DC motor driver based on the MC33886 chip. It allows you to control the movement of drives with a working voltage from 5 to 28 V and a current of up to 5 A