J-Link JTAG Isolator (8.07.00)
ID: 197715
5902186317345
zł1,031.90
Tax included
zł838.94 tax excl.
Standard 20-pin 0.1 male connector to provide electrical isolation, Segger
J-Link JTAG Isolator (8.07.00)
Standard 20-pin 0.1 male connector to provide electrical isolation, Segger
The J-Link JTAG Isolator can be connected between J-Link and any ARM-board that uses the standard 20-pin JTAG-ARM connector to provide electrical isolation. This is essential when the development tools are not connected to the same ground as the application. It is also useful to protect the development tools from electrical spikes that often occur in some applications, such as motor control applications. Another typical field of application is development of products with sensors or other analog circuitry, in which case the target hardware is protected from electrical noise originating from the development PC.
This product is compatible with J-Link, J-Link PRO, J-Link ULTRA, J-Link ULTRA+, J-Link PLUS and Flasher ARM.
Including all models, more than 100,000 J-Links have been sold so far, making J-Link probably the most popular emulator for ARM cores and the de-facto standard.
Features
- 1kV DC isolation
- 3.3V and 5V target operation supported
- Powered from emulator and target
- JTAG standard 20-pin connection supporting TRST, TDI, TMS, TCK, RTCK, TDO and RESET signals
- Power consumption on target side: < 50mA
- JTAG frequency: Up to 4MHz
- 3 LEDs to indicate emulator power, target power and target RESET
Connectors and indicators
The JTAG Isolator uses high speed optocouplers that allow a very low propagation time between input and output. It comes with the following connectors and indicators:
- 20-pin female EMULATOR connector which can be plugged directly into J-Link
- 20-pin male TARGET connector for connection of the target cable
- Green LED indicating power on the emulator side
- Green LED indicating power on the target side
- Red LED indicating RESET
Contents
- Segger J-Link JTAG Isolator
Download:
- J-Link JTAG Isolator webpage
- J-Link JTAG Isolator Documentation
- Artykuł w portalu Mikrokontroler.pl pt. "Programatory i debuggery firmy Segger (J-Link) - przegląd możliwości"
Code: J-Link JTAG Isolator (8.07.00)
197715
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
JTAG interface galvanic separator that protects equipment against damage caused by potential differences, with a maximum clock frequency of 110 MHz, 3-5 V power supply, and isolation voltage up to 1 kVDC, equipped with multiple connectors and optical status signaling
zł399.00
24h
Available quantity: 40
Available
Hi-Speed JTAG/SWD Emulator for ARM7/9, Cortex and Renesas RX cores with USB interface, Segger
zł4,131.40
24h
Available quantity: 2
Available
Hi-Speed JTAG/SWD Emulator with USB and Ethernet interface, Segger
zł5,221.25
24h
Available quantity: 3
Available
JTAG/SWD Emulator for ARM7/9, Cortex and Renesas RX cores with USB interface, Segger
zł3,097.52
24h
Available quantity: 6
Available
Flash Programmer for ARM and Cortex cores, Segger
zł4,101.91
24h
Available quantity: 1
Available
Available
Other products in the same category (16)
Professional reference board with ARM Cortex-M4F microcontroller, designed for code tracing and real-time application analysis. Equipped with an external 19-pin debug port and test points for trace signals, it enables easy integration with J-Link and J-Trace programmers, supporting Embedded Trace Macrocell (ETM) technology. Segger Cortex-M Trace Reference Board (6.68.18)
zł99.43
1 weeks
No product available!
The Intel FPGA Adapter (formerly J-Link Altera Adapter) connects to the Intel FPGA 10-pin JTAG connector, enabling debugging of FPGA-based MCU cores such as the dual-core Arm Cortex-A9 in Cyclone V devices. on Intel FPGA solutions.
zł254.71
1 weeks
No product available!
J-Link SDK one year Support and Update Agreement extension. Can only be purchased by customers with a J-Link SDK License (Model 8.08.06). Segger J-Link SDK Extension (8.08.18)
zł5,211.31
1 weeks
No product available!
SiFive-ARTY adapter for debugging between J-Link and the ARTY board with SiFive RISC-V. Segger SiFive-ARTY Adapter (8.06.24)
zł260.56
1 weeks
No product available!
Xilinx adapter that connects to Xilinx\'s 14-pin, 2mm JTAG connector, providing debugging of MCU cores such as the Arm Cortex-A9 on Xilinx Zynq FPGAs. With its compact design and high signal quality, it is a reliable tool for engineers working with FPGA platforms. Segger Xilinx Adapter (06/08/19)
zł256.43
1 weeks
No product available!
10-pin Needle Adapter to connect Flasher 5, Flasher ST7 or Flasher STM8 to a PCB, Segger
zł521.14
1 weeks
No product available!
A device that provides electrical isolation between the J-Trace emulator and the ARM board, which protects against electrical interference, especially in systems where the development tools and the application do not share the same ground. It provides 1 kV DC isolation, supports trace frequencies up to 75 MHz, and is compatible with J-Trace V2 and later versions, with a minimum power consumption of 25 µA. Segger J-Trace Isolator (07/08/10)
zł1,559.52
24h
Available quantity: 1
Available
J-Link 19-pin Cortex-M Adapter, RoHS, Segger
zł164.33
24h
Available quantity: 3
Available
A set of three SON/DFN adapters enables easy testing and programming of flash devices in these packages, eliminating the need for dedicated solutions for each form factor. The adapters are compatible with the SEGGER (Q)SPI Flash Evaluator and other test systems, making them a versatile tool for both test and production. SEGGER (Q)SPI Flash Evaluator Adapter board Pack for SON/DFN (6.40.03)
zł617.53
1 weeks
No product available!
An adapter that allows you to connect a 20-pin 0.1" connector to a 10-pin connector, allowing you to easily connect J-Link or Flasher programmers to your PCB using through-wires. It is ideal for prototyping, testing new designs and working with ST Discovery boards, offering flexibility, speed and time savings when making design changes.Segger Flying Wire Adapter (06.08.27)
zł355.88
1 weeks
No product available!
J-Link Needle Adapter - connect J-Link to a PCB, Segger
zł521.14
24h
Available quantity: 6
Available
The Segger J-Link Supply Adapter (8.06.14) allows you to manually set the debug probe I/O voltage, preventing damage to the target board, adjustable from 1.2V to 5.0V. It can be inserted between J-Link or Flasher and the target device, reducing the number of connections needed, which is especially useful in a production environment.
zł353.53
24h
Available quantity: 1
Available
Segger adapter 8.06.28 allows conversion from a 20-pin 0.1" connector to a 10-pin 0.05" Cortex-M type connector with the option of custom pin mapping. A useful solution for integrating programmers and debuggers with devices featuring different pin configurations.
zł254.71
24h
Available quantity: 1
Available
No product available!
The Segger J-Link Signal Smoothing Adapter (8/06/12) is designed to improve signal integrity between the J-Link debug probe and the target debug device. It allows JTAG signals to be suppressed by adjustable series resistors, preventing excessive gain and jitter.
zł260.56
1 weeks
No product available!
A compact reference platform that enables rapid testing and verification of trace configurations, providing excellent signal quality for analysis. With the ST STM32H743 microcontroller and support for JTAG, SWD and SWO debugging interfaces, the board provides high performance and flexibility in monitoring system performance. Segger STM32H7 Trace Reference Board (6.68.20)
zł1,036.19
1 weeks
No product available!
Standard 20-pin 0.1 male connector to provide electrical isolation, Segger