RP2350 MCU board with 1.28″ round LCD 240×240 - Waveshare 28986
ID: 1197465
5902186307322
zł60.26
Tax included
zł48.99 tax excl.
RP2350-LCD-1.28 is an advanced, compact development module with a color LCD display and a rich set of interfaces, designed for embedded projects that require efficient graphics handling and communication. Thanks to its dual processor architectures and programmable peripheral resources, the module is suitable for use in smart devices, HMI systems, and next-generation IoT solutions.
Description
RP2350-LCD-1.28 is a compact development module based on the RP2350 microcontroller designed by Raspberry Pi, combining the ARM Cortex-M33 architecture with the open RISC-V Hazard3 standard. The board features a 1.28-inch color LCD with a resolution of 240×240 pixels, an IMU sensor (accelerometer and gyroscope), a Li-Ion battery charging circuit, and 30 multifunction GPIO pins.
The device supports drag-and-drop programming via USB Type-C and offers UART, SPI, I2C, ADC, and PWM interfaces. The board's design allows direct integration into user devices, and the inclusion of 12 PIO state machines enables the creation of custom peripherals. It is suited for low-power operation modes and is supported by C/C++ and MicroPython libraries.
Features
- Microcontroller: RP2350 – 2× ARM Cortex-M33 + 2× Hazard3 RISC-V, up to 150 MHz
- Memory: 520 KB SRAM, 4 MB NOR Flash (P25Q32SH-UXH-IR)
- Display: 1.28” IPS, 240×240, 65K colors (non-touch)
- Sensors: QMI8658 (6DOF IMU), temperature sensor
- Interfaces: 2× SPI, 2× I2C, 2× UART, 4× 12-bit ADC, 24× PWM, 12× PIO
- Programming: USB 1.1 (host/device), drag-and-drop
- Power supply: USB Type-C, MX1.25 connector (3.7 V Li-Ion battery)
- GPIO: 30 pins via 1.27 mm female header (partially shared with internal circuits)
- Sleep and low-power operation modes
- Supported languages: C/C++ and MicroPython
- No enclosure – designed for embedded integration and prototyping
1197465
Data sheet
- Microcontroller
- RP2350
- Flash memory
- 4 MB
- Number of I/O
- 30
- Ethernet
- none
- WiFi/BT module
- No
- Bluetooth module
- No
- MicroSD slot
- No
- Length
- Inny
- Width
- Inna
- USB connector type
- USB type C
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
Base board with soldered Raspberry Pi Pico W module. Equipped with numerous connectors, buzzer, buttons and LEDs. Cytron MAKER-PI-PICO-MINI-W
zł64.23
24h
Available quantity: 3
Available
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0 + 133 MHz cores, 264 kB RAM. The board also has 8 MB of QSPI flash memory. The circuit can be programmed in C/C++, CircuitPython or MicroPython. Adafruit 5302
zł46.67
24h
Available quantity: 4
Available
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 264 kB RAM. The board also has 4 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Pimoroni PIM578
zł66.22
24h
Available quantity: 6
Available
RP2350-Zero-M combines compact dimensions with high performance and a rich set of peripherals. With pre-soldered headers and compatibility with popular development environments such as C/C++ and MicroPython, it is an ideal choice for creators of educational projects, embedded system prototypes, and IoT solutions.
zł24.88
24h
Available quantity: 2
Available
RP2350-USB-A is a versatile development board based on the modern RP2350A microcontroller with a unique dual-core architecture: Arm Cortex-M33 + RISC-V. Thanks to the USB Type-A port supported via PIO, a wide range of interfaces, and a compact form factor, the board is ideal for prototyping peripheral devices, learning programming, and integrating into custom projects as an SMD module.
zł23.85
24h
Available quantity: 11
Available
Board with RP2040 microcontroller and MCP2515 CAN controller. It has a built-in LiPo charging circuit and a STEMMA QT connector. It allows you to add communication based on the CAN bus to the project, commonly used in projects related to robotics and the automotive industry. Adafruit 5724
zł98.19
24h
Available quantity: 4
Available
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 264 kB RAM. The board also has 4 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Waveshare RP2040-Plus
zł23.27
24h
Available quantity: 11
Available
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0 + cores, which operate at a frequency of 133 MHz and 264 kB RAM. The additional ESP8285 system allows communication in the WiFi network. Seeed Studio 102991555
zł61.34
24h
Available quantity: 1
Available
Board with the RP2040 microcontroller in the form of a USB dongle. Equipped with edge connectors, RGB LED, boot and reset button. Waveshare RP2040-One
zł23.11
24h
Available quantity: 9
Available
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 264 kB RAM. The board also has 4 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Waveshare RP2040-Plus-M
Regular pricezł46.57zł35.94
24h
Available quantity: 3
Available
The RP2350-Plus-M offers the flexibility and performance required in modern embedded projects while maintaining full compatibility with Raspberry Pi Pico and its extensions. Factory-soldered headers and built-in Flash memory make the module suitable for rapid prototyping as well as educational and commercial applications.
zł28.93
24h
Available quantity: 6
Available
Raspberry Pi Pico 2WH, based on the RP2350 microcontroller and has a built-in WiFi and Bluetooth communication module. Pi Pico 2WH offers significantly increased performance and functionality thanks to the use of Cortex M33 and RISC-V cores, doubled SRAM memory and advanced security features, including Arm TrustZone. It is hardware and software compatible with previous models, making it an attractive choice for enthusiasts and professionals in the field of embedded systems. Version with soldered joints.
zł41.98
24h
Available quantity: 131
Available
Module with the RP2040 microcontroller with two ARM Cortex-M0 + cores operating at 133 MHz, 256 kB RAM and 30 GPIO. The board also has 2 MB of external QSPI flash memory. Module can be programmed in C/C++ or microPython. Version with soldered connectors. Raspberry Pi SC0917
zł23.90
24h
Available quantity: 37
Available
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores. The board also has 4 MB of QSPI flash memory. 1.14" LCD module. TTGO T-Display RP2040
zł84.85
24h
Available quantity: 4
Available
Module with round 1.28" IPS LCD display and 240x240 px resolution and RP2040 chip. SB Components 24018
zł190.51
24h
Available quantity: 4
Available
Mechanical keyboard module with LED backlight, encoder and display. Based on the RP2040 microcontroller. Adafruit 5128
zł264.54
24h
Available quantity: 2
Available
RP2350-LCD-1.28 is an advanced, compact development module with a color LCD display and a rich set of interfaces, designed for embedded projects that require efficient graphics handling and communication. Thanks to its dual processor architectures and programmable peripheral resources, the module is suitable for use in smart devices, HMI systems, and next-generation IoT solutions.