Best sellers

GNSS module based on the L76B chip that can work with GPS, BDS and QZSS systems. Communication via a UART interface. SB Components 24056

Board with the NB-IoT SIM7028 module intended for Raspberry Pi. It communicates via the UART interface and AT commands. Waveshare SIM7028-NB-IoT HAT (EN)

This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 150.58:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.

This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 9.96:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.

Switching power supply from MEAN WELL 30W, 5VDC output voltage and 6A output current. Mounting on a DIN rail. Built-in overload and short-circuit protection. MDR-40-5

GPS module with LC29H GNSS receiver designed to work with the Raspberry Pi minicomputer. It allows you to receive data from major positioning systems, including GPS, QZSS, GLONASS, Galileo and BeiDou, and supports positioning assistance systems (WAAS, EGNOS, MSAS and GAGAN) and EASY technology. Waveshare LC29H(AA) GPS HAT

Set of 10 cables, 30 cm long, for digital sensors compatible with the Gravity standard. DFRobot FIT0011

Module with 16 digital outputs. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP8027ADAM

Module with Flash memory W25Q16 with a capacity of 16 Mbit (2 MB). It communicates via the QSPI interface. Adafruit 5632

Lanberg Cat. 6A patch cord with Fluke Passed certification guarantees the highest quality and reliability, enabling optimal network connection compatible with various network devices in any environment. Lanberg PCF6A-10CC-0100-O

Housing for Raspberry Pi 3/2 / B + two-colored (black-transparent). Mounted on screws without the use of glue, made of plastic

Module with blue LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0031-B

Lanberg Cat. 6A patch cord with Fluke Passed certification guarantees the highest quality and reliability, enabling optimal network connection compatible with various network devices in any environment. Lanberg PCF6A-10CC-0200-G

Flexible cable (tape) 50 cm long, used to connect the camera module with Raspberry Pi computers. The tape has 15 wires and a pitch of 1mm

The Digilent Cmod A7 is a small, breadboard friendly 48-pin DIP form factor board built around a Xilinx Artix-7 FPGA. The board also includes a USB-JTAG programming circuit, USB-UART bridge, clock source, Pmod host connector, SRAM, Quad-SPI Flash, and basic I/O devices. 410-328

QUICK Q-T-SK series soldering tip designed for use in: 236/706/936A/3104/3102/TS1100

Module with green LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0021-G

Set for IR communication. It consists of an IR receiver module and a remote control. DFRobot DFR0107

Module with three 4-20 mA analog outputs. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP3078ADAM

Miniature high-power motor from the Pololu MP series. 100: 1 gear motor,
the rotation speed of the shaft is 220 rpm, the torque is 1.5 kg * cm (0.15 Nm).
The motor has an extended shaft which makes it easy to attach the encoder. Pololu 2381