Best sellers

Module with 5V relay and timer. It allows the implementation of delayed switching on or off of the circuit with adjustable time in the range from 1 s to 100 s and from 1 s to 15 min.

DFRobot 0592 is a Raspberry Pi DC motor driver board with built-in encoder interface that can drive a 2-way DC motor and a DC motor with encoder

Module with a capacitive fingerprint reader with UART and USB interface. Waveshare Capacitive Fingerprint Reader (B)

Camera with a resolution of 2 MPx with a USB interface. Equipped with a CMOS IMX291 sensor with an ultra-wide lens with a viewing angle of 120°, a microphone and a case. ArduCAM UB020101

Communication module with the system SIM7000G designed for minicomputers Raspberry Pi. Adds NB-IoT, eMTC, EDGE, GPRS and GNSS support. Waveshare SIM7000G NB-IoT HAT (EN)

Miniature, 12V brush DC motor with metal gear with 15.25: 1 ratio. It has a cross section of 10 × 12 mm, and the D-shaped output shaft has a length of 9 mm and a diameter of 3 mm. It also has an extended motor shaft with dimensions of 4.5 × 1 mm. Pololu 4789

Development kit with nRF52840 microcontroller with ARM Cortex M4F core and 2 MB external QSPI memory. It has built-in BLE communication. It can be programmed using the Arduino IDE or CircuitPython. Adafruit 45481

The 688ZZ bearing is a small, precision deep groove ball bearing with dimensions of 8×16×5 mm (inner diameter × outer diameter × thickness). It features double metal shields that protect against dust and small contaminants, although they are not fully waterproof. Ideal for use in model making, 3D printers, small electric motors, or guide rollers

Module with a 12 V relay and a timer. It allows you to turn the device on and off cyclically at a specified time using potentiometers. It can also operate in single trigger mode, which allows the device to be turned on after a signal has been applied for a specified period of time. The operating time can be adjusted from 1 s to 100 s or from 1 s to 15 min

Plotter with a laser with a power of 3000 mW and a beam length of 405 nm. It allows you to engrave in materials such as wood, plastics, rubber or thin leather. NEJE DK-8-KZ

Soldering station with 50 W soldering iron. Controlled analogously by means of a potentiometer. YIHUA 936

Portable digital oscilloscope with built-in signal generator and multimeter. It has two measuring channels with 80 MHz bandwidth and a single-channel signal generator with waveform frequencies up to 25 MHz. It offers a set of functions for automotive diagnostics. Hantek 2D82 AUTO III

Hot air soldering station with smooth regulation of air outlet. Digitally controlled, with display. YIHUA 858D

This sensor is a carrier/breakout board for ST’s VL6180X proximity and ambient light sensor, which measures the range to a target object up to 20 cm away (or 60 cm with reduced resolution). Pololu 2489

Plotter with a laser with a power of 1500 mW and a beam length of 405 nm. It allows you to engrave in materials such as wood, plastics, rubber or thin leather. NEJE DK-8-KZ

HAT with two-channel DC motor driver for Raspberry Pi. It has an operating voltage from 6 to 24 V and a continuous current of up to 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron HAT-MDD10

Minicomputer with the SOM STM32MP157C. It has a dual-core Arm® Cortex®-A7 and an Arm® Cortex®-M4, as well as a PMIC power supply system, 512MB RAM and 4GB eMMC. The set consists of the SOM module and the base board. Seeed Studio 102110319

The Quectel EM060K-GL is an LTE-A Cat 6 module in M.2 form, designed for industrial and commercial applications, compatible with many other Quectel modules. It offers broad compatibility with major operators with an integrated GNSS receiver that supports GPS, GLONASS, BDS and Galileo. Its rich set of network protocols and support for a variety of drivers make it ideal for applications ranging from industrial routers to digital signaling systems. Waveshare 24386

Module with a 3-color e-Paper display with a diagonal of 4.2" and a resolution of 400x300 px. Communication via the SPI interface. Waveshare Pico-ePaper-4.2-B

Camera module with OV9782 sensor designed for DepthAI systems, including the DM1090FFC base plate. ArduCAM B0335