Best sellers

RGB LED driver module equipped with ATtiny1616 microcontroller and STEMMA QT connector. It uses a 3.3V/5V voltage level converter and allows you to control the popular Neopixel LEDs. Adafruit 5766

Finder 38.51.0.024.0060 is an interface relay module with a 24 V AC/DC coil, equipped with a single changeover contact (SPDT) with a 6 A load capacity at 250 V AC. It is designed for DIN rail mounting, facilitating easy integration into industrial automation systems.

Brushless DC motor driver (BLDC) with speed regulation by potentiometer or PWM signal. It can operate motors powered with the voltage from 6 to 60 V with a current consumption of up to 16 A

Motor with 25 mm diameter and 58 mm length, 378:1 metal gear, 12 V operating voltage, 0,1 A to 1,1 A power consumption, 14 RPM speed and 23 maximum torque. Pololu 3258

USB adapter for PC, allowing Bluetooth v4.0 communication with speeds up to 3Mb / s and range up to 20m

The USB-C to DisplayPort cable allows for a direct connection of a monitor to a USB-C port, eliminating the need for additional adapters. With USB 3.2 Gen 2 bandwidth, it supports video transmission in up to 4K quality at 60Hz, ensuring clear visuals and smooth performance.  CA-CMDP-10CU-0010-BK

STM32 Nucleo-32 development board with STM32L031K6T6 MCU, supports Arduino connectivity

Finder 41.81.7.024.8240 is a solid-state relay (SSR) with one normally open contact (SPST-NO), capable of handling a maximum load current of 3 A and a load voltage range of 12–275 V AC. It is controlled by a 24 V DC input voltage and designed for PCB mounting, featuring compact dimensions of 29 x 12.7 x 15.7 mm.

The module is designed to support incremental encoders. It reads the rotation of the encoder and transmits the information via the I2C interface. It has two built-in STEMMA QT connectors. Adafruit 5740

At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much). Adafruit 2796

T-Cobbler adapter enabling connection of GPIO Raspberry Pi A +, B +, Pi 2 and Pi 3 lines to the contact plate (2.54 mm). Adapter assembled, including connecting tape

Switching power supply from MEAN WELL, power 40W, output voltage 12VDC and output current 3.33A. Mounting on a DIN rail. Built-in overload and short-circuit protection. MDR-40-12

The P10/10 electromagnet is a compact device designed for precise applications in automation and robotics, with dimensions of 10x10 mm, ideal for places with limited space. Powered by 24V, it generates a pulling force of 0.3N, making it ideal for light manipulation and latching operations.

This module enables the Feather series range to be expanded with 8 12-bit PWM outputs that can be used, for example, to control servos or LED diodes. Adafruit 2928

Module with 16x2 characters LCD display and ATMega328p microcontroller. The user can communicate with the module through one of the serial interfaces: UART, I2C or SPI. SparkFun LCD-16396

This is the FeatherWing OLED: it adds a 128x32 monochrome OLED plus 3 user buttons to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight. Adafruit 2900

LED strip with addressable RGB WS2813 diodes on a white PCB. It is powered by 5 V DC, has a length of 1 m and 60 LEDs/m. Protection level IP30

STM32 Nucleo-144 development board with STM32F303ZE MCU, supports Arduino, ST Zio and morpho connectivity

At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic. 256K FLASH, 32K RAM, built in USB and battery charging. Adafruit 2772

FeatherWing Doubler is a shield that allows you to create your own layout based on two or one Feather series. The plate has 256 holes, including designated, common solder points for supply voltages. Adafruit 2890