Best sellers
There are 16826 products.
The board is equipped with ATSAMD21 microcontroller with ARM Cortex-M0 core and SPI Flash memory, GPIO pins and RGB diode. Adafruit 3505
The overlay solves the problem of limitations in the use of multiple overlays compatible with Arduino UNO R3. The board allows you to connect different shields without their mutual influence on each other (eg without conflict on the UART bus or GPIO lines). Extension dedicated for Arduino Mega and ADK devices. DFRobot DFR0256
The S9V11F5 switching step-up/step-down regulator efficiently produces 5V from input voltages between 2V and 16V. Pololu 2836
A set of 10 cables for connecting Gravity modules to a set with a LattePanda minicomputer. DFRobot FIT0514
Stabilized laboratory power supply with programmable memory and smooth voltage regulation in the range from 0 to 30 V and smooth current regulation in the range from 0 to 5 A and 5 V, 3 A output. The power supply is distinguished by large precision LED displays that keep you informed about the current voltage and current load.
Stabilized power supply with programmable memory and smooth voltage regulation in the range of 0 ... 30 V and smooth current regulation in the range of 0 ... 5 A and output 5 V, 3 A. Design of the power supply based on the transformer. The power supply is distinguished by large precision LED displays that keep you informed about the current voltage and load.
Programmable Logic IC Development Tools Cyclone V SE 5CSEMA4U23C6N + 800MHz Dual-core ARM Cortex-A9 processor. Terasic P0496
Module with LM386 audio amplifier and loudspeaker. The board is equipped with a Grove connector and is controlled by a PWM signal. Seeed Studio 107020001
Module of the 3-axis LIS2DH, I2C accelerometer. DFRobot SEN0224
Flywires cable 2x16 designed for use with the Digilent Digital Discovery logic analyzer. Digilent 240-118
The DE10-Standard Development Kit presents a robust hardware design platform built around the Intel System-on-Chip (SoC) FPGA, which combines the latest dual-core Cortex-A9 embedded cores with industry-leading programmable logic for ultimate design flexibility. P0493
A set for building a balancing robot. It has a board with an ATmega 32u4 microcontroller, engine controllers, modules with quadrature encoders and an IMU system (gyroscope, accelerometer, magnetometer). Pololu 3575
Module with an analog current sensor. Enables measurement of alternating and direct current up to 20 A. DFRobot SEN0214
Controller module for building an arcade game dedicated to Raspberry Pi. Connectors placed on the board allow you to connect 6 momentary buttons, a joystick and a loudspeaker. Adafruit 3422
The CY7C65213 USB to UART serial breakout is designed to provide users with a means to access all available I/O pins on the IC, and to provide a 6-pin UART header that is compatible with other SparkFun breakout boards. This breakout has a microUSB connector and other support circuitry to get the IC quickly up and running. BOB-13830
It has 10 segments, one can be highlighted in red, one in yellow, one in light green, the rest in green. This type of display can be used to indicate battery charge, liquid level in the tank, volume etc. Seeed Studio 104020006
Gravity: 360 Degree Hall Angle Sensor is a rotation angle sensor measuring a value in the range of 0-360 ° with an analogue output, powered by 5V. DFRobot SEN0221
Switching power supply from MEAN WELL with 50W, 5V DC output voltage and 10A output current. Mounting on a DIN rail. Built-in overload and short-circuit protection. MDR-60-5
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V. BOB-12758
A module with a 24-bit ADC converter HX711, which allows you to read data from strain gauges and scales. It communicates via the serial interface. SparkFun SEN-13879