Terasic DE10-Standard (P0493) - ACADEMIC (EDU)

ATTENTION! This product is for academic recipients (students and academic teachers) only!

After the ordering, please send us by e-mail the data listed below:

• the name and last name
• position (student, teacher)
• e-mail (with the University domain)
• University name
• Facultie / Section
• University address
• University phone no.
• End user application

Description

Description

The DE10-Standard Development Kit presents a robust hardware design platform built around the Intel System-on-Chip (SoC) FPGA, which combines the latest dual-core Cortex-A9 embedded cores with industry-leading programmable logic for ultimate design flexibility. Users can now leverage the power of tremendous re-configurability paired with a high-performance, low-power processor system. Altera’s SoC integrates an ARM-based hard processor system (HPS) consisting of processor, peripherals and memory interfaces tied seamlessly with the FPGA fabric using a high-bandwidth interconnect backbone. The DE10-Standard development board includes hardware such as high-speed DDR3 memory, video and audio capabilities, Ethernet networking, and much more.

Features

• FPGA Device
  • Cyclone V SX SoC—5CSXFC6D6F31C6N
  • 110K LEs, 41509 ALMs
  • 5,761 Kbits embedded memory
  • 6 FPGA PLLs and 3 HPS PLLs
  • 1 Hard Memory Controller

• ARM®-Based Hard Processor System (HPS)
  • 925 MHz, Dual-Core ARM Cortex™-A9 MPCore™ Processor
  • 512 KB of Shared L2 Cache
  • 64 KB of Scratch RAM
  • Multiport SDRAM Controller with Support for DDR2, DDR3, LPDDR1, and LPDDR2
  • 8-Channel Direct Memory Access (DMA) Controller

• Configuration and Debug
  • Serial Configuration Device – EPCS128 on FPGA
  • On-Board USB Blaster II (Normal Type B USB Connector)

• Memory Device
  • 64MB (32Mx16) SDRAM on FPGA
  • 1GB (2x256Mx16) DDR3 SDRAM on HPS
  • MicroSD Card Socket on HPS

• Communication
  • Two USB 2.0 Host Ports (ULPI Interface with USB Type A Connector) on HPS
  • USB to UART (Micro USB Type B Connector) on HPS
  • 10/100/1000 Ethernet on HPS
  • PS/2 Mouse/Keyboard 
  • IR Emitter/Receiver

• Connectors
  • One 40-pin Expansion Header (Voltage Levels: 3.3V)
  • One HSMC Connector(Configurable I/O Standards 1.5/1.8/2.5/3.3V)
  • One 10-Pin ADC Input Header
  • One LTC Connector (One Serial Peripheral Interface (SPI) Master ,One I2C and One GPIO Interface ) on HPS

• Display
  • 24-bit VGA DAC
  • 128x64 Dots LCD Module with Backlight on HPS

• Audio
  • 24-bit CODEC, Line-in, Line-out, and Microphone-In Jacks

• Video Input
  • TV Decoder (NTSC/PAL/SECAM) and TV-In Connector

• ADC
  • Sample Rate: 500 KSPS
  • Channel Number: 8
  • Resolution: 12 bits
  • Analog Input Range : 0 ~ 4.096 V

• Switches, Buttons and Indicators
  • 4 User Keys (FPGA x4)
  • 10 User Switches (FPGA x10)
  • 11 User LEDs (FPGA x10 ; HPS x 1)
  • 2 HPS Reset Buttons (HPS_RST_n and HPS_WARM_RST_n)
  • 7-Segment Display x6

• Sensors
  • G-Sensor on HPS

• Power
  • 12V DC Input

Block Diagram of the DE10-Standard Board

Layout (Size:166*130 mm)

Kit contents:

1. DE10-Standard Board
2. DE10-Standard Quick Start Guide
3. Type A to B USB Cable
4. Type A to Mini-B USB Cable
5. Power DC Adapter (12V)
6. Four Silicon Footstands