Best sellers

Module with green LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0031-G

DC-DC Step-Up/Step-Down Converter Module. It has an input voltage of 1.4 to 16 V, an output voltage of 3.3 V and a maximum output current of 1 A to 1.5 A. Pololu 4964

Module with yellow LED, digitally controlled. Perfect for people starting to play with Arduino. Equipped with a Gravity interface. DFRobot DFR0031-Y

EXTREME heat shrink tubing for electrical and mechanical insulation, diameter against shrinkage 8.0mm; diameter after shrinkage 4.0 mm, a set of 10 pieces with a length of 1 meter

The inverter is powered by 12V DC, it generates alternating current to supply electroluminescent wires that glow under the influence of high voltage supply

The small 125mm side cutters allow for precise cutting in hard-to-reach places.

STM32H725VGT6, High-performance and DSP with DP-FPU, Arm Cortex-M7 MCU with 1 MByte Flash, 564 KBytes RAM, 550 MHz CPU, L1 cache, external memory interface, SMPS, subset of peripherals, LQFP100

Development board based on the ESP32-C3-MINI-1 module. It offers the ability to connect via WiFi, Bluetooth version 5 and Bluetooth Mesh. It is equipped with sensors, such as the SHTC3 temperature and humidity sensor or the IMU 6 DoF ICM-42670-P sensor. Espressif Systems ESP32-C3-DevKit-RUST-1

Module with a Panasonic sensor with an 8x8 IR thermal matrix (AMG8833 chip) with a built-in 3.3 V controller and a logic level translator. The I2C interface is used for communication. Adafruit 3538

An e-Paper display driver for the Raspberry Pi with the IT8951 chip, which provides smooth and efficient management of content display on e-Paper screens. It supports various communication interfaces, such as USB, SPI, and I80. Waveshare e-Paper Driver HAT

STM32H735VGT6, High-performance and DSP with DP-FPU, Arm Cortex-M7 MCU with 1 MByte Flash, 564 KBytes RAM, 550 MHz CPU, L1 cache, external memory interface, SMPS, subset of peripherals, LQFP100

STM32H735ZGT6, High-performance and DSP with DP-FPU, Arm Cortex-M7 MCU with 1 MByte Flash, 564 KBytes RAM, 550 MHz CPU, L1 cache, external memory interface, SMPS, subset of peripherals, LQFP144

Touch light switch with WiFi and RF that can control one lighting circuit in the room. It allows you to independently turn on/off the light and set time schedules using the eWeLink application. Sonoff T3EU1C TX

Permanent cylindrical neodymium magnet with a diameter of 3 mm and a height of 10 mm. Set of 10 pcs

Universal multimeter that allows to measure DC and AC voltage, DC and AC current and resistance. Equipped with circuit continuity test and backlight, among other features. ANENG M107

Touch light switch with WiFi and RF that can control two lighting circuit in the room. It allows you to independently turn on/off the light and set time schedules using the eWeLink application. Sonoff T3EU2C TX

The LOGO! 8 consists of a Siemens LOGO! 8, power cables and KA-LOGO! -IO-Simulator simulation board with output terminal board. Thanks to this set, it is possible to quickly and easily start learning programming of the logic module.

Evaluation board with ATSAMD21 microcontroller with ARM Cortex M0 core. Equipped with motion, temperature, light, sound sensors and RGB diodes. Can be programmed in MakeCode, CircuitPython, Arduino IDE or CS Discoveries. Adafruit 3333

Universal multimeter that allows to measure DC and AC voltage, DC and AC current, frequency, capacitance and resistance. Equipped with diode tester, circuit continuity test and transistor testing function, among others. ANENG SZ08

Sonoff MINI is a universal WiFi controlled switch. It has a small size and can be mounted in a standard flush-mounted box behind the lighting switch. Sonoff MINI