Best sellers
There are 16461 products.
Switching power supply from MEAN WELL, power 40W, output voltage 24VDC and output current 1.7A. Mounting on a DIN rail. Built-in overload and short-circuit protection. MEAN WELL MDR-40-24
Nozzle designed for 3D printers with a Volcano hotend. It is much longer than standard V6 nozzles, which makes it possible to achieve higher print speeds
Stainless steel crimped cable ties with dimensions of 8.0 x 600 mm are an indispensable tool for anyone who needs a durable, reliable and safe solution for securing and organizing cables and pipes. Thanks to high quality workmanship, ease of installation and safety of use, they are ideal for professionals from various industries. Yato YT-70588
WiFi module based on ESP8266. It has an embedded antenna and 0.96 "OLED display. The module can be programmed in Lua (under NodeMCU firmware control) or in the Arduino IDE. Provides 12 GPIO lines.
High-quality Yato YT-3246 wood drill, ideal for precise and deep drilling. YT-3246
A magnetic latching relay that features low power consumption and quiet operation. It allows switching of signals up to 36 V and 10 A. It remains in the last position it was in before power was lost. DFRobot DFR0996
YATO YT-33021 confirmat drill, made of durable steel, with a three-stage design and a cylindrical handle with a diameter of 8 mm, intended for precise drilling of holes for furniture screws in wood and wood-based materials in one work cycle, ideal for furniture production. YT-33021
High-quality Yato YT-4080 cylindrical drill with a diameter of 8 mm, ideal for drilling in stainless steel, stainless steel, acid-resistant steel, cast iron, non-ferrous metals and plastics. Yato YT-4080
The VOREL 66330 special bit set is a reliable tool, offering a wide selection of bits and a 60 mm adapter, ideal for many service and repair applications. Vorel-66330
A tester for 1.5V and 9V batteries, which does not require a power supply, allows a simple assessment of the battery condition by touching the poles with the metal terminals, with the measurement results under load indicating green (GOOD), yellow (LOW) and red (REPLACE, RECHARGE) fields, compact and easy to store. Sthor-81700
Nozzle designed for 3D printers with the popular MK8 hotend. The Teflon coating prevents the filament from sticking to the nozzle
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 264 kB RAM. The board also has 8 MB of QSPI flash memory. The circuit can be programmed in C/C++, CircuitPython or MicroPython. Adafruit 4900
Universal diamond disc for angle grinders, equipped with a continuous turbo segment with a height of 8 mm, intended for wet or dry operation, ideal for cutting hardened and reinforced concrete, brick, granite, masonry, stone and sandstone, at a recommended speed of approximately 11,000 rpm ./min. YT-6023
Diamond disc for angle grinders, intended for dry operation, recommended for cutting ceramics, concrete, stone and brick, equipped with segments 7 mm high and 2.3 mm thick, with recommended revolutions of approximately 8400/min. Sthor-08782
The Step-Down D24V3F5 Buck Voltage Regulator module gives the output voltage of 5V with a wide input voltage range of 7-42V and a maximum output current of 300 mA. Pololu 2098
Female-female cable, 16 cm long, with JST-SH 6-pin plug on both sides. Suitable for micro DC motor encoders with gear. Pololu 4766
30 cm nickel-titanium alloy wire with shape memory. When it is in martensitic form, it can be flexed and deformed at will. After applying a current of about 1.5A or heating to 100°C, the wire returns to its original shape. SparkFun COM-11900
Universal diamond disc for angle grinders with a 7 mm continuous turbo segment, designed for wet or dry operation, recommended for cutting concrete, bricks, stone and other building materials, with a recommended speed of approximately 12,000 rpm. Vorel-08751
ACS711EX Current Sensor Carrier -31A to +31A