<Border = 0>
<Border = 0>Description
The Arduino Wireless Proto Shield is a great solution for XBee (TM) compatible socket .
You can use the wireless module from Digi to create a network of Arduino boards, solder parts to the prototyping area to create your project.
The shields breaks out the XBee's pins to a through-hole solder pad. It provides pin headers for all Arduino pins.
Board comes fully assembled and tested.
Code: A000064
Manufacturer
Dual-channel electric motors controller (H-bridge) Arduino Motor Shield Rev3 with L298 for controlling two DC motors or one stepper motor with the possibility of using an electronic brake.
No product available!
RF module providing wireless communication compliant with the IEEE 802.15.4 standard. They operate in the 2.4 GHz ISM band and enable local configuration via BLE with the Digi XBee mobile application. They are equipped with the Silicon Labs EFR32MG SoC transmitter and receiver chipset. The range in buildings is up to 90 m, while in open space it reaches up to 3200 m. SparkFun WRL-22629
Base board for prototyping IoT applications using the new Digi XBee 3 Low-Power LTE-M/NB-IoT and Digi XBee RR modules. It gives access to the full functionality of the XBee module pins, including two USB Type-C connectors for UART communication and firmware updates, a Qwiic connector for I2C-compatible sensors and peripherals. SparkFun WRL-21636
Advanced expansion shield for Arduino. Supports SIM cards as well as NB-IoT / CAT-M cards. With the integrated GNSS (Global Navigation Satellite System) module, it supports GPS, GLONASS, Galileo and BeiDou navigation systems. The module is powered with a voltage from 7 V to 12 V. DFRobot DFR0572
Shield designed for IoT applications with LTE CAT M1/NB-IoT SARA-R4 modem. The board is compatible with Arduino, allows you to add communication via cellular networks to Arduino boards. SparkFun CEL-14997
Cap for Xbee and Arduino. It has been designed for wireless sensor networks such as WiFi, Bluetooth 2.0 / 4.0 and Zigbee. DFRobot DFR0015
Ethernet extension for Arduino based on the Wiznet W5100S chip, enabling a microcontroller to connect to a LAN network via an RJ45 connector. The module supports a hardware TCP/IP stack, up to 4 simultaneous network connections, and includes a microSD card slot, communicating with Arduino through the SPI interface. DFRobot DFR0125
NFC module designed for Arduino. Meets the standards of reader mode, P2P mode and card emulation mode. The board has an integrated RF antenna. NXP OM5578/PN7150ARDM
Expansion board with 4G/3G/2G communication module and GNSS positioning. The kit has pins compatible with Arduino and STM32 Nucleo. DFRobot TEL0124
Expansion board with GSM/GPRS module designed for Arduino and Raspberry Pi. It uses the Quectel M95 chip, the board has two audio connectors, a microSD slot and a dual SIM slot. A-GSM II Shield
No product available!
Ethernet network module with W5500 chip and PoE (Power over Ethernet) function. It communicates via the SPI interface, it has a built-in TCP/IP stack. DFRobot DFR0850
Ethernet network module with W5500 chip. It communicates via the SPI interface, it has a built-in TCP/IP stack. There are two Grove connectors with I2C and UART on the board. Seeed Studio 103030021
CAN module based on MCP2551 and MCP2515 systems with an OBD-II compatible connector. It uses the I2C or UART bus (Grove connectors) for communication. Seeed Studio 103030215
The Arduino expansion board is dedicated to applications that use NB-IoT communication. Thanks to the GNSS (Global Navigation Satellite System) module, it supports GPS, GLONASS, Galileo, QZSS and BeiDou navigation systems. The module is supplied with the voltage from 7 to 12 V. DFRobot DFR0572
Expansion board based on the Wiznet W5200 Ethernet chip. It allows you to easily connect the Arduino to the Ethernet network. DFRobot DFR0272
UART-RS485 converter module. It enables communication of Arduino boards with industrial modules. DFRobot DFR0259
Board with the GNSS Cinterion TX62 module with support for Cat. M1 and NB IoT. Dedicated for Arduino Portenta H7. Arduino ASX00027
No product available!
Module with Himax HM-01B0 camera and Ethernet communication dedicated to Arduino Portenta H7 boards. Arduino ASX00021
No product available!
Module with Himax HM-01B0 camera and LoRa communication dedicated to Arduino Portenta H7 boards. Arduino ASX00026
No product available!
Arduino Wireless Shield