CAN-BUS Shield V2 - CAN module with MCP2551 and MCP2515
ID: 1178616
5906623415779
zł113.14
Tax included
zł91.98 tax excl.
CAN module based on MCP2551 and MCP2515 systems with an OBD-II compatible connector. It uses the I2C or UART bus (Grove connectors) for communication. Seeed Studio 103030215
Description
CAN module based on MCP2551 and MCP2515 dedicated to Arduino. It uses the I2C bus for communication, which can operate at a maximum frequency of 400 kHz. The MCP2551 chip is a high-speed, fault-tolerant CAN transceiver that serves as an interface between the CAN protocol controller and the physical bus. Provides differential transmission and reception for CAN protocol controller and is fully compatible with ISO-11898 standard. The MCP2515 is a 2nd generation standalone CAN controller. It offers high bandwidth, data byte filtering, and support for time-triggered protocols. The CAN bus communication speed can reach up to 1 Mb/s. The board has a D-sub connector compatible with OBD-II, a microSD slot and a Grove connector with a UART interface. Full documentation is available on the product page.
Features
- CAN communication module
- Transmission speed up to 1Mb / s
- TX and RX LED indicator for CAN bus
- 9-pin D-sub socket compliant with the OBD-II standard
- 4-pin Grove connector with I2C and UART
- MicroSD card slot
- Working voltage 3.3 / 5V
- Easy-to-use Arduino library
- Dimensions: 74.8 x 53.4 27.1 mm
1178616
Data sheet
- Communication
- CAN
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface
zł53.71
24h
Available quantity: 20
Available
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.42
24h
Available quantity: 55
Available
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
zł24.40
24h
Available quantity: 21
Available
4-core cable, 20 cm long, terminated on both sides with a Grove plug. Compatible with the interface used in Seeed Studio and M5Stack modules. Seeed Studio 110990027
zł8.87
24h
Available quantity: 8
Available
A 4-core cable with a length of 50 cm, both terminated with a Grove plug. Seeed Studio 110990038
zł15.19
24h
Available quantity: 3
Available
Other products in the same category (16)
Expansion board based on the Wiznet W5200 Ethernet system. It allows you to easily connect Arduino to an Ethernet network. DFRobot DFR0125
zł75.73
24h
Available quantity: 1
Available
Module with Himax HM-01B0 camera and LoRa communication dedicated to Arduino Portenta H7 boards. Arduino ASX00026
zł489.00
3 weeks
No product available!
Arduino compatible shield for the ESP8266 WiFi SoC – a leading platform for Internet of Things (IoT) or WiFi-related projects. WRL-13287
zł93.33
3 weeks
No product available!
UART-RS232 converter module. It enables communication of Arduino boards with industrial modules. DFRobot DFR0258
zł49.94
4 weeks
No product available!
Module with a radio receiver operating at 315 MHz for Arduino. DFRobot TEL0075
zł33.73
24h
Available quantity: 1
Available
A wireless overlay designed for Arduino tiles. Equipped with a connector compatible with Xbee modules and a microSD card slot. Arduino A100065
zł97.39
24h
Available quantity: 1
Available
Ethernet network module with W5500 chip and PoE (Power over Ethernet) function. It communicates via the SPI interface, it has a built-in TCP/IP stack. DFRobot DFR0850
zł133.79
4 weeks
No product available!
Ethernet network module with W5500 chip. It communicates via the SPI interface, it has a built-in TCP/IP stack. There are two Grove connectors with I2C and UART on the board. Seeed Studio 103030021
zł144.30
24h
Available quantity: 3
Available
Shield for STM32 series Nucleo, XNucleo and Arduino series for communication via RS485 and CAN interfaces (CAN is only available for Nucleo and XNucleo plates). Shield is based on MAX3485 and SN65HVD230 systems
zł39.45
24h
Available quantity: 6
Available
NFC module designed for Arduino. Meets the standards of reader mode, P2P mode and card emulation mode. The board has an integrated RF antenna. NXP OM5578/PN7150ARDM
zł39.90
24h
Available quantity: 31
Available
The Arduino expansion board is dedicated to applications that use NB-IoT communication. Thanks to the GNSS (Global Navigation Satellite System) module, it supports GPS, GLONASS, Galileo, QZSS and BeiDou navigation systems. The module is supplied with the voltage from 7 to 12 V. DFRobot DFR0572
zł260.44
24h
Available quantity: 1
Available
KAmodNFC is an expansion board with M24LR64E-R chip – dynamic tag with 64kb EEPROM memory and dual communication interface (I2C/RF). On board is placed also signalization of energy harvesting function, which is in M24LR64E-R chip embedded.
zł28.91
24h
Available quantity: 212
Available
Adafruit 789 - Adafruit PN532 NFC/RFID Controller Shield for Arduino + Extras
zł235.56
24h
Available quantity: 1
Available
The Arduino Ethernet Shield 2 allows an Arduino Board to connect to the internet. It is based on the Wiznet W5500 Ethernet chip. The Wiznet W5500 provides a network (IP) stack capable of both TCP and UDP. There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega
zł129.00
3 weeks
No product available!
Expansion board based on the Wiznet W5200 Ethernet chip. It allows you to easily connect the Arduino to the Ethernet network. DFRobot DFR0272
zł115.02
24h
Available quantity: 1
Available
Ethernet board with mini SD card slot based on W5100 controller.
zł35.36
4 weeks
No product available!
CAN module based on MCP2551 and MCP2515 systems with an OBD-II compatible connector. It uses the I2C or UART bus (Grove connectors) for communication. Seeed Studio 103030215