New products
New products New products
zł301.74
24h
Dostępny
Available
Available
zł59.04
24h
Available
RF Shield (315MHz) radio module for Arduino
ID: 231745
5902186311169
zł33.73
Tax included
zł27.42 tax excl.
Module with a radio receiver operating at 315 MHz for Arduino. DFRobot TEL0075
Description
The RF 315 MHz module is a receiver with a wide range of applications in remote control devices, security installations and data terminals. This module is compatible with sensors / controllers 315MHz, using SC2260, SC2262, PT2260, PT2262. Intended for use with Arduino
Application:
- Remote, wireless control
- Small data terminal
- Alarm Systems
properties
- Interface compatible with Arduino
- Carrier frequency: 315MHz
- Power consumption: 10mA (max.)
- Modulation: ASK
- Receiver type: superheterodyne
- Sensitivity: -102dBm (typical), -98dBm (worst)
- Transmission rate: 9.6kb / s (max.)
- Bandwidth of the received band: ± 1.25MHz (6dB)
- Antenna impedance: 75Ω
- Decoder: SC2272
- Data output: compatible with CMOS levels
- The possibility of attaching an Xbee module
- Range: <40 m (open space)
- Working temperature: 0 ℃ to 70 ℃
- Arduino pins used: digital pins: 3,8,9,10,11
231745
Data sheet
- Communication
- Radio
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Module with Himax HM-01B0 camera and LoRa communication dedicated to Arduino Portenta H7 boards. Arduino ASX00026
zł489.00
Delivery date unknown
No product available!
Other products in the same category (16)
Advanced expansion board for Arduino. It has support for mini-SIM cards and NB-IoT cards. Thanks to the GNSS module (Global Navigation Satellite System), it supports GPS, GLONASS, Galileo, QZSS and BeiDou GPS navigation systems. The module is powered by 7-12V voltage. DFRobot DFR0572
zł234.98
24h
Available quantity: 1
Available
CAN module based on MCP2551 and MCP2515 systems with an OBD-II compatible connector. It uses the I2C or UART bus (Grove connectors) for communication. Seeed Studio 103030215
zł113.14
4 weeks
No product available!
Shield designed for IoT applications with LTE CAT M1/NB-IoT SARA-R4 modem. The board is compatible with Arduino, allows you to add communication via cellular networks to Arduino boards. SparkFun CEL-14997
zł720.77
24h
Available quantity: 1
Available
Expansion board with 4G/3G/2G communication module and GNSS positioning. The kit has pins compatible with Arduino and STM32 Nucleo. DFRobot TEL0124
zł468.65
24h
Available quantity: 1
Available
NFC module designed for Arduino. Meets the standards of reader mode, P2P mode and card emulation mode. The board has an integrated RF antenna. NXP OM5578/PN7150ARDM
zł39.90
24h
Available quantity: 30
Available
Board with the GNSS Cinterion TX62 module with support for Cat. M1 and NB IoT. Dedicated for Arduino Portenta H7. Arduino ASX00027
zł455.68
3 weeks
No product available!
Ethernet board with mini SD card slot based on W5100 controller.
zł35.36
4 weeks
No product available!
Ethernet network module with W5500 chip and PoE (Power over Ethernet) function. It communicates via the SPI interface, it has a built-in TCP/IP stack. DFRobot DFR0850
zł133.79
4 weeks
No product available!
UART-RS232 converter module. It enables communication of Arduino boards with industrial modules. DFRobot DFR0258
zł49.94
4 weeks
No product available!
Expansion board with GSM/GPRS module designed for Arduino and Raspberry Pi. It uses the Quectel M95 chip, the board has two audio connectors, a microSD slot and a dual SIM slot. A-GSM II Shield
zł204.67
6 weeks
No product available!
Shield with LTE CAT M1/NB-IoT SARA-R4 modem. Compatible with Arduino. Hologram SIM card included. SparkFun CEL-15087
zł587.25
3 weeks
No product available!
KAmodNFC is an expansion board with M24LR64E-R chip – dynamic tag with 64kb EEPROM memory and dual communication interface (I2C/RF). On board is placed also signalization of energy harvesting function, which is in M24LR64E-R chip embedded.
zł28.91
24h
Available quantity: 212
Available
The Arduino expansion board is dedicated to applications that use NB-IoT communication. Thanks to the GNSS (Global Navigation Satellite System) module, it supports GPS, GLONASS, Galileo, QZSS and BeiDou navigation systems. The module is supplied with the voltage from 7 to 12 V. DFRobot DFR0572
zł260.44
24h
Available quantity: 1
Available
Connect your Arduino-compatible to the Internet with this WiFi shield that features the FCC-certified ATWINC1500 module from Atmel. Adafruit 3654
zł125.28
24h
Available quantity: 1
Available
A wireless overlay designed for Arduino tiles. Equipped with a connector compatible with Xbee modules and a microSD card slot. Arduino A100065
zł97.39
24h
Available quantity: 1
Available
The Arduino Ethernet Shield 2 allows an Arduino Board to connect to the internet. It is based on the Wiznet W5500 Ethernet chip. The Wiznet W5500 provides a network (IP) stack capable of both TCP and UDP. There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega
zł129.00
3 weeks
No product available!
Module with a radio receiver operating at 315 MHz for Arduino. DFRobot TEL0075