Ethernet Shield - W5200 Ethernet module for Arduino
ID: 1179250
5902186310490
zł93.97
Tax included
zł76.40 tax excl.
Expansion board based on the Wiznet W5200 Ethernet chip. It allows you to easily connect the Arduino to the Ethernet network. DFRobot DFR0272
Description
Expansion board based on the Wiznet W5200 chip. It allows you to easily connect the Arduino to the Ethernet network. To access Arduino via the Internet, just connect the module to the network with a cable (not included) and follow a few simple steps from the instructions. The arrangement of pins allows for stacking modules. The board is equipped with a heat sink to remove excess heat.
The W5200 has a built-in TCP/IP stack and an integrated Ethernet MAC & PHY. The TCP/IP stack supports the TCP, UDP, IPv4, ICMP, ARP, IGMP, and PPPoE protocols that have proven themselves in a variety of applications for many years. Uses an internal 32KB buffer as memory for data transmission.
The module can be used in devices such as home network devices (set-top box, PVR, digital media center), USB Ethernet (mass storage devices, network printers), security systems (network camera) or an embedded server. Full documentation is available on the product page.
Features
- TCP/IP protocol support: TCP, UDP, ICMP, IPv4 ARP, IGMP, PPPoE, Ethernet
- It supports 8 independent slots simultaneously
- Power off mode support
- Wake on LAN support
- Support for high-speed serial peripheral interface (SPI mode 0, 3)
- 32 KB internal memory for Tx/Rx buffers
- Built-in 10BaseT/100BaseTX Ethernet PHY technology
- Support for autonegotiation (full and half duplex, 10 and 100 based)
- Auto MDI/MDIX support
- ADSL connection support (with PPPoE support with PAP / CHAP authentication mode)
- 3.3V operation with 5V I/O signal tolerance
- Multifunctional LED outputs (Full/Half duplex, Link, Speed)
1179250
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.57
24h
Available quantity: 191
Available
Available
Ethernet patch cord UTP 5E, 2 m long. Red color, with RJ45 connectors. Lanberg Z22990
zł3.00
24h
Available quantity: 21
Available
Other products in the same category (16)
BASIC-programmable Ethernet Module, Tibbo Technology, RoHS
zł221.40
24h
Available quantity: 3
Available
Available
Available
Universal module supervised by the website, which can control both DC circuits as well as powered from 230 V mains. The states of digital inputs, relays and control buttons are presented on the website. AVTMOD05
zł403.19
24h
Available quantity: 1
Available
The Arduino Ethernet Shield 2 allows an Arduino Board to connect to the internet. It is based on the Wiznet W5500 Ethernet chip. The Wiznet W5500 provides a network (IP) stack capable of both TCP and UDP. There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega
zł129.00
3 weeks
No product available!
The module allows the existence of devices with BLE in networks with the Ethernet protocol, has a BT2.1 receiver
zł226.32
24h
Available quantity: 1
Available
Ethernet module with WIZ5500 chip and RJ45 connector. It allows you to connect the Feather series boards to a wired network. Adafruit 3201
zł106.85
24h
Available quantity: 4
Available
The transceiver module of the DP83848 Ethernet interface
zł45.74
24h
Available quantity: 2
Available
Ethernet extension for Arduino based on the Wiznet W5100S chip, enabling a microcontroller to connect to a LAN network via an RJ45 connector. The module supports a hardware TCP/IP stack, up to 4 simultaneous network connections, and includes a microSD card slot, communicating with Arduino through the SPI interface. DFRobot DFR0125
zł64.92
24h
Available quantity: 4
Available
Carrier board dedicated to Raspberry Pi CM4 modules. It is equipped with two Ethernet connectors, a microSD slot and a USB connector. It allows you to build a small router. DFRobot DFR0767
zł253.27
24h
Available quantity: 6
Available
USB 3.2 Gen1 to Gigabit Ethernet converter based on the efficient Realtek RTL8153 controller. It is compatible with Win7 / 8 / 8.1 / 10, Mac, Linux and Android systems. Waveshare USB 3.2 Gen1 TO Gigabit ETH
zł64.10
24h
Available quantity: 1
Available
Miniature Ethernet network module with W5500 chip. It has compact dimensions, so it can be used as an element of another device
zł30.90
4 weeks
No product available!
Ethernet network module with W5500 chip. Supports up to 8 independent sockets simultaneously
zł17.54
24h
Available quantity: 118
Available
Ethernet network module with W5500 chip and PoE (Power over Ethernet) function. It communicates via the SPI interface, it has a built-in TCP/IP stack. DFRobot DFR0850
zł132.67
24h
Available quantity: 2
Available
2-channel converter that provides easy communication between the UART TTL serial interface and RJ45 Ethernet. Waveshare 2-CH UART TO ETH
zł44.24
24h
Available quantity: 7
Available
Ethernet network module with W5100S chip dedicated to Raspberry Pi Pico. It communicates via the SPI interface and works with 3.3 V and 5 V systems. WIZnet-Ethernet-HAT
zł28.06
24h
Available quantity: 26
Available
Expansion board based on the Wiznet W5200 Ethernet chip. It allows you to easily connect the Arduino to the Ethernet network. DFRobot DFR0272