DEV-10864 OSHW - PoEthernet Shield
Description: Ethernet connectivity is a great way to get your Arduino talking to other systems all over the world (or at least the network). But sometimes running an Ethernet cable is hard enough, why should you have to run a power cable too? Thats where PoE comes into play: Power over Ethernet. The PoEthernet Shield not only give your Arduino access to the Internet via the Ethernet Library but it also allows your project to power itself from the Ethernet line (provided youve injected power to it somewhere down the line).
The way this is accomplished is that the unused data pairs of the RJ-45 connector broken out to the 4-pin header in the corner of the shield. The V- pin on that header breaks out the 7 & 8 pair of RJ-45 pins, and the V+ pin breaks out the 4 & 5 pair. You can use a couple of jumpers to connect those pins to GND and VIN respectively. This will send the PoE through the Arduino, to be regulated to 5 and 3.3V. This works really well with our passive PoE cable set! The shield also includes an SD card slot that can be accessed using the SD library.
Note: This is not 802.3af-compatible PoE, its more of a home-brew Power-over-Ethernet scheme that we like to call "DIY PoE." You shouldnt apply anything outside the 7-12V range to those pins (The input voltage range of the Arduino board) unless you regulate the power off-board.
Documents:
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Module with Himax HM-01B0 camera and Ethernet communication dedicated to Arduino Portenta H7 boards. Arduino ASX00021
No product available!
A USB host module that contains all the digital logic and analog circuitry necessary to implement a USB peripheral or host controller using the SPI interface. SparkFun DEV-21247
No product available!
Module with a radio receiver operating at 315 MHz for Arduino. DFRobot TEL0075
Shield for STM32 series Nucleo, XNucleo and Arduino series for communication via RS485 and CAN interfaces (CAN is only available for Nucleo and XNucleo plates). Shield is based on MAX3485 and SN65HVD230 systems
Shield with LTE CAT M1/NB-IoT SARA-R4 modem. Compatible with Arduino. Hologram SIM card included. SparkFun CEL-15087
No product available!
Expansion board based on the Wiznet W5200 Ethernet chip. It allows you to easily connect the Arduino to the Ethernet network. DFRobot DFR0272
Introducing Adafruit FONA 808 GSM + GPS Shield, an all-in-one cellular phone module with that lets you add location-tracking, voice, text, SMS and data to your project, in Arduino shield format for easy use. Adafruit 2636
No product available!
UART-RS485 converter module. It enables communication of Arduino boards with industrial modules. DFRobot DFR0259
Adafruit 789 - Adafruit PN532 NFC/RFID Controller Shield for Arduino + Extras
No product available!
Expansion board with GSM/GPRS module designed for Arduino and Raspberry Pi. It uses the Quectel M95 chip, the board has two audio connectors, a microSD slot and a dual SIM slot. A-GSM II Shield
No product available!
Shield designed for IoT applications with LTE CAT M1/NB-IoT SARA-R4 modem. The board is compatible with Arduino, allows you to add communication via cellular networks to Arduino boards. SparkFun CEL-14997
CAN module based on MCP2551 and MCP2515 systems with an OBD-II compatible connector. It uses the I2C or UART bus (Grove connectors) for communication. Seeed Studio 103030215
No product available!
Ethernet network module with W5500 chip. It communicates via the SPI interface, it has a built-in TCP/IP stack. There are two Grove connectors with I2C and UART on the board. Seeed Studio 103030021
The CAN-BUS Arduino Shield v2.0 can be stacked on an Arduino UNO, Arduino Leonardo or Arduino MEGA board. The shield integrates an MCP2515 CAN-BUS chip on the shield and has a CAN-BUS transceiver function. With an on-board DB9 and CAN-BUS connector you can choose a suitable port according to your host device. There is also an integrated MicroSD socket for data storage. DFR0370
Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.
Ethernet network module with W5500 chip and PoE (Power over Ethernet) function. It communicates via the SPI interface, it has a built-in TCP/IP stack. DFRobot DFR0850
DEV-10864 OSHW - PoEthernet Shield