STEMMA QT INA228 Power Monitor - module with INA228 power monitor
search
  • STEMMA QT INA228 Power Monitor - module with INA228 power monitor
  • STEMMA QT INA228 Power Monitor - module with INA228 power monitor
  • STEMMA QT INA228 Power Monitor - module with INA228 power monitor
  • STEMMA QT INA228 Power Monitor - module with INA228 power monitor
ID: 1188213
5906623490592
zł75.05
Tax included

zł61.02 tax excl.

Module with INA228 sensor designed for power monitoring. It allows you to measure voltages up to 85 VDC and currents up to 10 A. It uses a 20-bit ADC converter, which guarantees very precise and accurate measurements available via the I2C bus. Adafruit 58332

24h
Available
Available quantity: 4
Kamami is the official distributor of Adafruit modules and development kits. All boards of this brand in our offer are original and come directly from the manufacturer.

Description

The INA228 sensor module is a power monitoring device that provides comprehensive measurement support. This powerful tool allows you to measure voltages up to 85 VDC in common voltage mode, allows measurement on a low or high voltage line, has a 20-bit ADC converter for precise current measurements from milliamps to amperes, as well as an I2C interface for easy configuration of alarms, oversampling , gain adjustment and many other functions. The module works with microcontrollers or single-board computers such as Raspberry Pi. It is compatible with both 3V and 5V logic.

The sensor allows for accurate measurements at various voltage, current and temperature ranges with an accuracy of better than 1%, and all data is easily accessible via the I2C interface. Thanks to the precision 15 mOhm resistor built into the board, the module can be used to measure voltages up to +85 V at a current of up to 10 A in continuous mode on both low and high voltage lines. The module uses a built-in 20-bit resolution ADC, which allows for accurate measurements over an impressive current range, with a resolution of 10uA per LSB in high-current measurement mode or 2.5uA per LSB in low-current measurement mode.

The INA228 module is an indispensable tool for precise power monitoring over a wide range of voltages and currents. Thanks to I2C support and exceptional 20-bit resolution, this module significantly exceeds the capabilities of traditional solutions available on the market.

Features

  • High resolution 20-bit delta-sigma ADC
  • Current Monitoring Accuracy:
    • Offset voltage: ±1 µV
    • Offset drift: ±0.01 µV/°C
    • Gain error: ±0.05%
    • Gain error drift: ±20 ppm/°C
    • Common mode rejection: 154 dB
    • Power Monitoring Accuracy: 0.5%
    • Energy and charging accuracy: 1%
  • Fast alarm response: 75 μs
  • Wide common mode range: –0.3V to +85V
  • Bus voltage detection input: 0V to 85V
  • Full shunt differential range: ±163.84 mV / ±40.96 mV
  • Input bias current: 2.5 nA
  • Programmable resistor temperature compensation
  • Programmable conversion and averaging time
  • Fast I2C interface: 2.94MHz with 16 selectable addresses
  • 2 x STEMMA QT connector (Qwiic)
  • Screw connection
  • Supply voltage: 2.7V to 5.5V
  • Dimensions: 25.8 x 20.2 x 10.1 mm

Kit contains

  • STEMMA QT INA228 Power Monitor module
  • Goldpin male straight 8-pin connector
1188213

Data sheet

Interface
I2C
Zakres pomiarowy
0 - 10 A
Sposób podłączenia
Szeregowy

Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20

Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20

You might also like

Other products in the same category (16)