ACS724 Current Sensor Carrier - ACS724 ±2.5A current sensor module
ID: 1186901
5906623469277
zł39.31
Tax included
zł31.96 tax excl.
ACS724LLCTR-2P5AB current sensor module with a DC and AC measurement range from -2.5 to +2.5 A. It communicates via an analog interface. Pololu 4040
Description
Module with a two-way Hall current sensor based on the ACS724LLCTR-2P5AB chip. It allows you to measure the current in the range from -2.5 to 2.5 A. The board is powered with the voltage from 4.5 V to 5.5 V and is intended for use in circuits with a logical voltage of 5 V. It offers a current path with low resistance (~ 1.2 mΩ) and electrical insulation up to 2.4 kV RMS. The output is a proportional analog voltage (800 mV/A) centered at 2.5 V with an error of ± 1.5%.
The sensor requires five connections to work properly: input current (IP+ and IP-), logic power (VCC and GND) and sensor output (OUT). Pin FILTER allows you to adjust the bandwidth of the plate by adding a capacitor to ground in parallel with the 1 nF capacitor that is already on the board. Without an additional external filter capacitor, the frequency response is approximately 90 kHz.
Features
- Hall effect differential detection
- Internal resistance of 1.2 mΩ conducting path
- Electrical insulation up to 2.4 kV RMS
- 120kHz high bandwidth for fast response times
- Ability to filter the output data to improve the resolution
- Integrated digital temperature compensation circuit
- Operating voltage 4.5 to 5.5 V
- Current measuring range from -2.5 to 2.5 A
- Output resolution 0.8 V/A
- Working temperature range from -40°C to 150°C
- Dimensions: 17.8 x 20.3 mm
- Weight: 1.1 g
Kit contains
- ACS724 Current Sensor Carrier module
- Straight 3-pin male connector
1186901
Data sheet
- Interface
- Sygnał analogowy
- Zakres pomiarowy
- ±2,5 A
- Sposób podłączenia
- Szeregowy
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Bidirectional current sensor module based on the ACS724 circuit. It allows you to measure current in the range -50A to + 50A. It operates with a voltage of 4.5V to 5.5V and is intended for use in 5V systems. Pololu 4049
zł51.82
Delivery date unknown
No product available!
Module with ACS724LLCTR-30AU current sensor with a measuring range of direct and alternating current from 0 to 30 A. It communicates via an analog interface. Pololu 4046
zł40.55
24h
Available quantity: 3
Available
Module with ACS724LLCTR-10AU current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4042
zł45.61
24h
Available quantity: 2
Available
Other products in the same category (16)
ACS714 Current Sensor Carrier -30 to +30A
zł49.70
24h
Available quantity: 2
Available
ACS711EX Current Sensor Carrier -31A to +31A
zł19.98
24h
Available quantity: 4
Available
ACS711EX Current Sensor Carrier -15.5A to +15.5A
zł20.06
24h
Available quantity: 5
Available
The current measurement of 0 - 30A is carried out by the ACS712-30 system based on the Hall effect. The sensitivity of the system is 66mV / A (analog signal).
zł6.86
4 weeks
No product available!
Available
No product available!
No product available!
No product available!
No product available!
The current measurement with the value 0-20A is carried out by the ACS712-05 system based on the Hall effect. The sensitivity of the system is 100mV / A (analogue signal) .modACS712-20
zł14.97
24h
Available quantity: 23
Available
The current measurement with a value of 0 - 5A is realized by the ACS712-05 system based on the Hall effect. The system sensitivity is 185mV / A (analog signal).
zł8.95
4 weeks
No product available!
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
zł92.27
24h
Available quantity: 1
Available
The module with a TA12-200 current sensor with a measuring range of alternating current up to 5 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020027
zł41.34
24h
Available quantity: 1
Available
Module with an analog current sensor. Enables measurement of alternating and direct current up to 20 A. DFRobot SEN0214
zł40.22
24h
Available quantity: 1
Available
Module with INA219 system with bi-directional current meter
zł10.01
4 weeks
No product available!
Module with a current and voltage sensor dedicated to Feather boards. Can measure voltage up to 26 V and current up to 3.2 A. Based on INA219 sensor, I2C communication. Adafruit 3650
zł44.90
24h
Available quantity: 1
Available
ACS724LLCTR-2P5AB current sensor module with a DC and AC measurement range from -2.5 to +2.5 A. It communicates via an analog interface. Pololu 4040