ACS37041KLHBLT-030B5 Current Sensor Compact - module with current sensor -30A to +30A, 5V
ID: 1197864
zł17.10
Tax included
zł13.90 tax excl.
A compact Hall-effect current sensor that provides accurate DC and AC current measurement within a ±30 A range with galvanic isolation. It features a high-sensitivity analog VOUT output with a 150 kHz bandwidth, enabling fast and precise readings in dynamic systems. The module operates over a wide temperature range of -40°C to 125°C, and the low current path resistance minimizes energy loss. Its small size and flexible mounting options make it ideal for prototyping, industrial systems, and space-constrained projects. Pololu 5447
Description
ACS37041 Micro Carrier is a compact module based on the Allegro current sensor, utilizing Hall effect technology and providing galvanic isolation for measurements. The device features a very low current path resistance, minimizing energy loss and ensuring high accuracy for both DC and AC current measurements. The analog output offers a wide 150 kHz bandwidth, allowing fast and precise current measurement in dynamic circuits. The sensor response time is less than 5 µs, making it ideal for applications requiring rapid response.
The module has five essential pins: current inputs IP+ and IP-, logic supply VDD and GND, and signal output VOUT. Power should be connected to the VDD and GND pads marked on the bottom of the board. The VOUT output generates an analog signal with a resting voltage of 2.5 V, which changes proportionally to the input current. Positive current increases the output voltage, while negative current decreases it.
The board can be integrated into the current path in various ways, depending on the application. In typical high-current applications, wires up to 10 AWG can be soldered directly to the mounting holes. These holes are also compatible with M3.5 mounting holes and screw terminals with a 3.5 mm or 5 mm pitch, facilitating module installation in prototype and final setups. Alternatively, goldpin connectors can be used, although they are not recommended for high currents.
The sensor provides integrated temperature compensation, increasing accuracy across the full operating temperature range of -40°C to 125°C, according to automotive standards. The device is non-ratiometric, meaning its zero point and sensitivity are independent of supply voltage fluctuations, ensuring noise immunity. Its compact size makes it ideal for small projects.
Features
- Sensor: ACS37041KLHBLT-030B5
- Measurement range: ±30 A (bidirectional)
- Supply voltage: 4.5 V to 5.5 V (nominal 5 V)
- Sensitivity: 66.7 mV/A
- Zero point: 2.5 V
- Current path resistance: ~1.6 mΩ
- Bandwidth: 150 kHz
- Response time: < 5 µs
- Temperature compensation
- Operating temperature: -40°C to 125°C
- Galvanic isolation: 100 Vrms
- Dimensions: 17.8 x 20.3 mm
1197864
Data sheet
- Interface
- Sygnał analogowy
- Zakres pomiarowy
- ±30 A
- Sposób podłączenia
- Szeregowy
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Pin header goldpin black 1x40 pins. Straight connector for through-hole assembly. 2.54mm pitch.
zł1.23
24h
Available quantity: 5383
Available
Pin header goldpin black 1x40 pins. Angled connector for through-hole assembly. 2.54mm pitch.
zł1.23
24h
Available quantity: 19249
Available
2-pin ARK mounting strip, 3.5 mm pitch. 381-3.5-02P-14-00AH
Delivery date unknown
No product available!
2-pin ARK mounting strip, 3.5 mm pitch. 381-3.5-02P-14-00AH. Set of 10 pieces
zł7.23
24h
Available quantity: 8
Available
Other products in the same category (16)
A compact Hall-effect current sensor that provides accurate DC and AC current measurement within a ±30 A range with galvanic isolation. It features an analog VOUT output with a sensitivity of 44 mV/A and a 150 kHz bandwidth, enabling fast and precise readings in dynamic systems. The module operates over a wide temperature range of -40°C to 125°C, and the low current path resistance (~1.6 mΩ) minimizes energy loss. Its small size and flexible mounting options make it ideal for prototyping, industrial systems, and space-constrained projects. Pololu 5441
zł15.89
4 weeks
No product available!
Module with ACS724 current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4045
zł44.72
4 weeks
No product available!
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5251
zł58.78
24h
Available quantity: 2
Available
Pololu 5242 with the ACS71240KEXBLT-050B3 chip is a compact current sensor module for precision measurement applications in the ±50 A range. With galvanic isolation, fast response to current changes, and short-circuit detection capability, it is used in power systems, automotive and industrial electronics, and embedded projects. It is ideal for measuring currents in both DC and AC circuits while ensuring safety and accuracy.
zł22.16
24h
Available quantity: 3
Available
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 10 A. DFRobot SEN0288
zł108.03
24h
Available quantity: 10
Available
This board is a simple carrier of Broadcom’s bidirectional ±50A ACHS-7125 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. Pololu 4034
zł17.72
24h
Available quantity: 3
Available
Precision Hall effect current sensor offering galvanic isolation, wide 150 kHz bandwidth and the ability to measure AC and DC current with very low power loss. With differential measurement and immunity to magnetic interference, it is perfect for applications requiring accurate current monitoring, such as power supplies, converters or motor control systems. Pololu 5290
zł28.28
24h
Available quantity: 4
Available
ACS724LLCTR-20AU current sensor module with a current measurement range from 0 to 20 A. It communicates via an analog interface. Pololu 4044
zł42.14
24h
Available quantity: 2
Available
The current measurement with a value of 0 - 5A is realized by the ACS712-05 system based on the Hall effect. The system sensitivity is 185mV / A (analog signal).
zł8.70
24h
Available quantity: 1
Available
A non-contact magnetic field sensor with a range of ±1.5 mT and a sensitivity of 1500 mV/mT at 5 V. It offers an analog ratiometric output and a flag signal activated when field thresholds are exceeded. It features a fast response time (20 µs) and a 30 kHz bandwidth with a built-in RC filter. Its compact design, AC/DC capability, and easy mounting make it ideal for energy-efficient and safe current monitoring systems. Pololu 5352
zł18.77
4 weeks
No product available!
ACS724LLCTR-2P5AB current sensor module with a DC and AC measurement range from -2.5 to +2.5 A. It communicates via an analog interface. Pololu 4040
zł39.31
24h
Available quantity: 2
Available
Module with ACS724LLCTR-10AU current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4042
zł50.36
24h
Available quantity: 2
Available
Compact current sensor based on TMR technology, enabling precise measurements up to 20 A with minimal energy loss. Thanks to a wide 1 MHz bandwidth, galvanic isolation and interference immunity, it is perfect for applications requiring fast response and high accuracy. Pololu 5304
zł52.79
24h
Available quantity: 2
Available
Voltage and current sensor module. It works with a shunt resistor and voltage divider and the INA-169 chip and can measure voltages up to 52 V and currents up to 45 A. SparkFun SEN-16407
zł136.90
3 weeks
No product available!
Voltage and current sensor module. It works with a shunt resistor and voltage divider and the INA-169 chip and can measure voltages up to 52 V and currents up to 90 A. SparkFun SEN-16408
zł136.90
3 weeks
No product available!
The ACS71240 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 120 kHz) and low conduction resistance (0.6 mΩ), it minimizes energy loss and offers a fast response time of less than 5 µs. Pololu 5245
zł21.37
24h
Available quantity: 3
Available
A compact Hall-effect current sensor that provides accurate DC and AC current measurement within a ±30 A range with galvanic isolation. It features a high-sensitivity analog VOUT output with a 150 kHz bandwidth, enabling fast and precise readings in dynamic systems. The module operates over a wide temperature range of -40°C to 125°C, and the low current path resistance minimizes energy loss. Its small size and flexible mounting options make it ideal for prototyping, industrial systems, and space-constrained projects. Pololu 5447