zł39.00
ACS37800KMACTR-030B3-I2C Power Monitor - power monitor with isolated I2C circuit
ID: 1197879
zł133.97
Tax included
zł108.92 tax excl.
This module provides precise, galvanically isolated current measurement within a range of ±30 A and voltage up to 480 VRMS, providing RMS, instantaneous, and active, reactive, and apparent power readings. Equipped with an I²C interface, 4-pin JST SH connectors, and 2.54 mm pins, it allows for easy integration with Qwiic, STEMMA QT, and standard microcontrollers. Configuration stored in EEPROM allows for defining address and overload thresholds. The sensor offers three voltage measurement ranges (120 V - default, 240 V, 480 V RMS) and the ability to detect overvoltages. Built-in protection and low conduction resistance ensure safe and accurate measurements. Pololu 5410
Description
The ACS37800KMACTR-030B3-I2C Power Monitor is an advanced measurement board based on Allegro Microsystems’ IC, designed to monitor voltage, current, power, and other parameters in both AC and DC systems. The device enables bidirectional current measurement from −30 A to +30 A and voltage measurement up to 480 VRMS (±980 V peak). With galvanic isolation on the measurement path and secondary isolation on the I²C interface, the module ensures high measurement accuracy and user safety.
The sensor provides RMS and instantaneous readings, automatically detects zero crossings, and calculates active, reactive, and apparent power as well as the power factor. With a 1 kHz bandwidth, it is suitable for a wide range of energy and industrial applications. The integrated Hall-effect current sensor offers an isolated current path, low conduction resistance (0.85 mΩ), and high common-mode noise immunity. The board includes a network of sense resistors optimized for 120 VAC, 240 VAC, and 480 VAC operation, allowing adaptation to various applications.
The module communicates via I²C, accessible through JST SH 4-pin connectors (compatible with Qwiic and STEMMA QT) or standard 2.54 mm pins. Configuration is stored in EEPROM, allowing customization of device address and detection thresholds. The default I²C address is 0x60. Logic is powered from 3 V to 5.5 V, while the integrated isolated DC-DC converter supplies the sensor with 3.3 V.
The ACS37800 sensor measures current flowing from the IP+ to IP− terminals, marked with a +i arrow indicating positive current direction. Voltage is measured between IP+ and V− points on the left side of the board, with positive readings corresponding to higher voltage on IP+. All left-side through-holes are electrically connected, allowing connection of power to internal points and load to external points.
The board has two surface-mount jumpers that configure one of three voltage measurement ranges for the ACS37800 sensor. These ranges are optimized for 120 V, 240 V, and 480 VAC RMS. Each range allows overvoltage detection, supporting transient voltages ~40% above nominal peak voltage. This enables measurement up to twice the nominal RMS before sensor saturation, increasing measurement safety and accuracy. By default, the jumpers are open, allowing measurements up to 120 VRMS.
The module also features an EN input to disable logic power for energy savings. Multiple connection options are provided: large 4 mm holes (up to 10 AWG or ring terminals), screw terminals with 9.5–12 mm pitch, and smaller 2.54 mm and 5.08 mm pads for pin headers. The board includes isolation slots to increase creepage distance, making it versatile for mounting and ideal for energy, industrial, and laboratory measurement applications.
Features
- Current and voltage sensor based on ACS37800KMACTR-030B3-I2C
- Current measurement range: −30 A to +30 A
- RMS and instantaneous current and voltage measurements
- Calculates active, reactive, and apparent power and power factor
- Bandwidth: 1 kHz
- Automatic zero-crossing detection
- Hall-effect current sensor with isolated measurement path
- Low conduction resistance: 0.85 mΩ
- Supports single-phase AC and DC systems
- Configurable voltage measurement ranges: 120 VAC, 240 VAC, 480 VAC
- Interface: I²C via JST SH 4-pin or 0.1″ pins
- Compatible with Qwiic and STEMMA QT
- Default I²C address: 0x60; configurable via EEPROM
- Programmable thresholds: overcurrent, undervoltage, overvoltage
- Logic power: 3 V to 5.5 V
- Isolated DC-DC converter supplying 3.3 V to sensor
- Secondary I²C isolation for enhanced safety
- EN input for logic power control
- Multiple mounting options: large holes (10 AWG), screw terminals, pin headers
- Board includes isolation slots for increased creepage distance
- Dimensions: 48.26 × 45.72 mm
1197879
Data sheet
- Interface
- I2C
- Zakres pomiarowy
- ±30 A
- Sposób podłączenia
- Szeregowy
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
This module provides precise, galvanically isolated current measurement within a range of ±30 A and voltage up to 480 VRMS, providing RMS, instantaneous, and active, reactive, and apparent power readings. Equipped with an I²C interface, 4-pin JST SH connectors, and 2.54 mm pins, it allows for easy integration with Qwiic, STEMMA QT, and standard microcontrollers. Configuration stored in EEPROM allows for defining address and overload thresholds. The sensor offers three voltage measurement ranges (120 V - default, 240 V, 480 V RMS) and the ability to detect overvoltages. Built-in protection and low conduction resistance ensure safe and accurate measurements. The version comes with soldered screw terminals and a 240 Vrms jumper. Pololu 5412
zł191.44
Delivery date unknown
No product available!
This module provides precise, galvanically isolated current measurement within a range of ±30 A and voltage up to 480 VRMS, providing RMS, instantaneous, and active, reactive, and apparent power readings. Equipped with an I²C interface, 4-pin JST SH connectors, and 2.54 mm pins, it allows for easy integration with Qwiic, STEMMA QT, and standard microcontrollers. Configuration stored in EEPROM allows for defining address and overload thresholds. The sensor offers three voltage measurement ranges (120 V - default, 240 V, 480 V RMS) and the ability to detect overvoltages. Built-in protection and low conduction resistance ensure safe and accurate measurements. The version comes with soldered screw terminals. Pololu 5411
zł172.30
Delivery date unknown
No product available!
Other products in the same category (16)
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
zł100.82
24h
Available quantity: 2
Available
Voltage and current sensor module. It works with a shunt resistor and voltage divider and the INA-169 chip and can measure voltages up to 52 V and currents up to 90 A. SparkFun SEN-16408
zł136.90
3 weeks
No product available!
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5273
zł71.45
24h
Available quantity: 5
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5257
zł58.79
24h
Available quantity: 2
Available
A compact Hall-effect current sensor that provides accurate DC and AC current measurement within a ±10 A range with galvanic isolation. It features an analog VOUT output with a sensitivity of 200 mV/A and a 150 kHz bandwidth, enabling fast and precise readings in dynamic systems. The module operates over a wide temperature range of -40°C to 125°C, and the low current path resistance (~1.6 mΩ) minimizes energy loss. Its small size and flexible mounting options make it ideal for prototyping, industrial systems, and space-constrained projects. Pololu 5442
zł15.89
4 weeks
No product available!
A compact Hall-effect current sensor that provides accurate DC and AC current measurement within a ±30 A range with galvanic isolation. It features a high-sensitivity analog VOUT output with a 150 kHz bandwidth, enabling fast and precise readings in dynamic systems. The module operates over a wide temperature range of -40°C to 125°C, and the low current path resistance minimizes energy loss. Its small size and flexible mounting options make it ideal for prototyping, industrial systems, and space-constrained projects. Pololu 5455
zł19.13
4 weeks
No product available!
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5260
zł58.79
24h
Available quantity: 2
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5263
zł58.79
24h
Available quantity: 5
Available
ACS711EX Current Sensor Carrier -15.5A to +15.5A
zł21.86
24h
Available quantity: 8
Available
Available
Compact current sensor based on TMR technology, enabling precise measurements up to 30 A with minimal energy losses. Thanks to a wide 1 MHz bandwidth, galvanic isolation and interference immunity, it is perfect for applications requiring fast response and high accuracy. Pololu 5317
zł52.79
4 weeks
No product available!
The ACS72981 current sensor module uses the Hall effect to precisely and safely measure DC current while providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes power loss and offers a fast response time of less than 2 µs. Pololu 5264
zł52.79
4 weeks
No product available!
HSTS08L 10A 2.5V Current Sensor. Enables measurement of high currents. modHSTS08L
zł71.86
24h
Available quantity: 3
Available
Module with a current and voltage sensor dedicated to Feather boards. Can measure voltage up to 26 V and current up to 3.2 A. Based on INA219 sensor, I2C communication. Adafruit 3650
zł44.90
24h
Available quantity: 2
Available
A compact Hall-effect current sensor that provides accurate DC and AC current measurement within a ±30 A range with galvanic isolation. It features an analog VOUT output with a sensitivity of 66.7 mV/A and a 150 kHz bandwidth, enabling fast and precise readings in dynamic systems. The module operates over a wide temperature range of -40°C to 125°C, and the low current path resistance (~1.6 mΩ) minimizes energy loss. Its small size and flexible mounting options make it ideal for prototyping, industrial systems, and space-constrained projects. Pololu 5443
zł15.89
4 weeks
No product available!
This module provides precise, galvanically isolated current measurement within a range of ±30 A and voltage up to 480 VRMS, providing RMS, instantaneous, and active, reactive, and apparent power readings. Equipped with an I²C interface, 4-pin JST SH connectors, and 2.54 mm pins, it allows for easy integration with Qwiic, STEMMA QT, and standard microcontrollers. Configuration stored in EEPROM allows for defining address and overload thresholds. The sensor offers three voltage measurement ranges (120 V - default, 240 V, 480 V RMS) and the ability to detect overvoltages. Built-in protection and low conduction resistance ensure safe and accurate measurements. The version comes with soldered screw terminals and a 240 Vrms jumper. Pololu 5412
zł191.44
4 weeks
No product available!
This module provides precise, galvanically isolated current measurement within a range of ±30 A and voltage up to 480 VRMS, providing RMS, instantaneous, and active, reactive, and apparent power readings. Equipped with an I²C interface, 4-pin JST SH connectors, and 2.54 mm pins, it allows for easy integration with Qwiic, STEMMA QT, and standard microcontrollers. Configuration stored in EEPROM allows for defining address and overload thresholds. The sensor offers three voltage measurement ranges (120 V - default, 240 V, 480 V RMS) and the ability to detect overvoltages. Built-in protection and low conduction resistance ensure safe and accurate measurements. Pololu 5410