

ACS711EX Current Sensor Carrier -31A to +31A
This board is a simple carrier of Allegro’s Âą31 A ACS711 Hall effect-based linear current sensor with overcurrent fault output, which offers a low-resistance (~0.6 mO) current path and electrical isolation up to 100 V. This version accepts a bidirectional current input with a magnitude up to 31 A and outputs a proportional analog voltage centered at Vcc/2 with a typical error of Âą4%. It operates from 3 V to 5.5 V, so it can interface directly to both 3.3 V and 5 V systems.
![]() |
![]() |
This current sensor is a carrier board or breakout board for Allegro’s ACS711KEXLT-31AB-T Hall effect-based linear current sensor with overcurrent fault output; we therefore recommend careful reading of the ACS711 datasheet (551k pdf) before using this product. This sensor has an operating voltage of 3 V to 5.5 V and an output sensitivity of 45 mV/A when Vcc is 3.3 V (or 68 mV/A when Vcc is 5 V). The following list details some of the sensor’s key features:
The pads are labeled on the bottom silkscreen, as shown in the picture to the right. The silkscreen also shows the direction that is interpreted as positive current flow via the +i arrow.
This 31 A current sensor is marked with a green X. We also sell a 15.5 A version that uses the same carrier PCB; you can distinguish the versions by reading the text on the IC or by looking at the color of the X on the bottom silkscreen.
This sensor is very similar to our original ACS711 -25 to +25 A Current Sensor Carrier, but uses a smaller “EX” package that has a larger optimized sensing range and reduced internal resistance. The board size, pinout, and hole locations are all unchanged, so it can generally be used as a drop-in replacement for our ACS711 carriers with “LC” packages.
The sensor requires a supply voltage of 3 V to 5.5 V to be connected across the Vcc and GND pads, which are labeled on the bottom silkscreen. The sensor outputs an analog voltage that is linearly proportional to the input current. The quiescent output voltage is Vcc/2 and changes by 45 mV per amp of input current (when Vcc = 3.3 V), with positive current increasing the output voltage and negative current decreasing the output voltage. The relationship between the instantaneous input current, i, and sensor output voltage, VOUT, can be represented by the following equations:
![]() |
The FAULT pin is normally high and latches low when the current exceeds Âą31 A. Once the FAULT pin is latched low, the only way to reset it is by toggling power on the Vcc pin. In our tests, this module was able to handle 31 A of continuous current without exceeding 100°C, with no cooling beyond the heat dissipation of the PCB.
|
|
The input current can be connected to the board in a variety of ways. Holes with 0.1", 3.5 mm, and 5 mm spacing are available as shown in the diagram above for connecting male header pins or terminal blocks. For high-current applications, you can solder wires directly to the through-holes that best match your wires, or you can use solderless ring terminal connectors, as shown in the picture above. The large through-holes are big enough for #6 screws.
Warning: This product is intended for use below 30 V. Working with higher voltages can be extremely dangerous and should only be attempted by qualified individuals with appropriate equipment and protective gear.
The board has two mounting holes on the logic side of the board. These mounting holes are 0.5" apart and are designed for #2 screws.
This board ships assembled with all surface mount components, and a 5×1 strip of 0.1" header pins is included but not soldered in, as shown in the picture below.
![]() |
ACS711EX current sensor carrier with included 5 × 1 0.1" header pins. |
---|
![]() |
ACS711 current sensor carrier schematic diagram. |
---|
![]() |
ACS711EX Current Sensor Carrier -15.5A to +15.5A |
![]() |
ACS709 Current Sensor Carrier -75A to +75A |
![]() |
LPS331AP Pressure/Altitude Sensor Carrier with Voltage Regulator |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
ACS714 Current Sensor Carrier -30 to +30A
Precision Hall effect current sensor offering galvanic isolation, wide 150 kHz bandwidth and the ability to measure AC and DC current with very low power loss. With differential measurement and immunity to magnetic interference, it is perfect for applications requiring accurate current monitoring, such as power supplies, converters or motor control systems. Pololu 5296
ACS711EX Current Sensor Carrier -15.5A to +15.5A
Module with an analog current sensor. It enables the measurement of AC and DC current up to 50 A. DFRobot SEN0098
No product available!
The ACS71240 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 120 kHz) and low conduction resistance (0.6 mΩ), it minimizes energy loss and offers a fast response time of less than 5 µs. Pololu 5243
No product available!
ACS724LLCTR-20AU current sensor module with a current measurement range from 0 to 20 A. It communicates via an analog interface. Pololu 4044
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5272
Module with ACS724LLCTR-30AU current sensor with a measuring range of direct and alternating current from 0 to 30 A. It communicates via an analog interface. Pololu 4046
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5259
Allegro\'s TMR sensor module enables precise, non-contact current measurement without breaking the circuit. It offers high sensitivity, low power consumption, an analog output proportional to the magnetic field, and a threshold detection (FLAG) function. Its compact design, AC/DC support, and easy installation make it ideal for energy-efficient and safe current monitoring systems. Pololu 5355
No product available!
The current measurement with the value 0-20A is carried out by the ACS712-05 system based on the Hall effect. The sensitivity of the system is 100mV / A (analogue signal) .modACS712-20
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
Module with bi-directional current sensor based on the INA226 system. It allows you to measure current and power, works with a voltage of 0-36 V. It has an I2C interface.
A non-contact magnetic field sensor with a range of ±1.5 mT and a sensitivity of 1500 mV/mT at 5 V. It offers an analog ratiometric output and a flag signal activated when field thresholds are exceeded. It features a fast response time (20 µs) and a 30 kHz bandwidth with a built-in RC filter. Its compact design, AC/DC capability, and easy mounting make it ideal for energy-efficient and safe current monitoring systems. Pololu 5352
No product available!
The ACS71240 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 120 kHz) and low conduction resistance (0.6 mΩ), it minimizes energy loss and offers a fast response time of less than 5 µs. Pololu 5244
The ACS71240 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 120 kHz) and low conduction resistance (0.6 mΩ), it minimizes energy loss and offers a fast response time of less than 5 µs. Pololu 5240
No product available!
ACS711EX Current Sensor Carrier -31A to +31A