New products
New products
zł609.00
Delivery date unknown
zł462.10
24h
Available
ACHS-7121 Current Sensor Carrier - ACHS-7121 ± 10A current sensor module
ID: 586601
5906623487967
zł17.55
Tax included
zł14.27 tax excl.
Module with ACHS-7121 current sensor with a measuring range of direct and alternating current from -10 to 10 A. It communicates via an analog interface. Pololu 4030
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Module with a bidirectional Hall current sensor based on the ACHS-7121 system. It allows you to measure the current in the range from -10 to 10 A. The board is powered with the voltage from 4.5 V to 5.5 V and is intended for use in circuits with a logical voltage of 5 V. It offers a current path with low resistance (~ 0,7 mΩ) and electrical insulation up to 3 kV RMS. The output is a proportional analog voltage (185 mV/A) centered at 2.5 V with an error of ± 1.5%.
The sensor requires five connections to work properly: input current (IP+ and IP-), logic power (VCC and GND) and sensor output (OUT). Pin FILTER allows you to adjust the bandwidth of the plate by adding a capacitor to ground in parallel with the 1 nF capacitor that is already on the board. Without an additional external filter capacitor, the frequency response is approximately 80 kHz.
Features
- Hall effect differential detection
- The internal resistance of the conductive path is 0.7 mΩ
- Electrical insulation up to 3 kV RMS
- High bandwidth up to 80kHz for fast response times
- Integrated digital temperature compensation circuit
- The rugged sensor IC can tolerate 100 ms to 100 A transient currents
- Operating voltage 4.5 to 5.5 V
- Current measuring range from -10 to 10 A
- Output resolution 0.185 V/A
- Operating temperature range from -40°C to 110°C
- Dimensions: 17.8 x 20.3 mm
- Weight: 1.1 g
Kit contains
- ACHS-7121 Current Sensor Carrier module
- Straight 3-pin male connector
586601
Data sheet
- Interface
- Sygnał analogowy
- Zakres pomiarowy
- ±10 A
- Sposób podłączenia
- Szeregowy
You might also like
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
zł100.82
24h
Available quantity: 2
Available
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 5A. DFRobot SEN0287
zł89.19
24h
Available quantity: 2
Available
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.01
24h
Available quantity: 776
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł3.94
Delivery date unknown
No product available!
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.62
Delivery date unknown
No product available!
Module with ACS724LLCTR-10AU current sensor with a measuring range of direct and alternating current from 0 to 10 A. It communicates via an analog interface. Pololu 4042
zł81.72
24h
Available quantity: 3
Available
Other products in the same category (16)
Module with INA219 system with bi-directional current meter
zł10.41
6 weeks
No product available!
Module with ACHS-7123 current sensor with a measuring range of direct and alternating current from -30 to 30 A. It communicates via an analog interface. Pololu 4032
zł17.86
24h
Available quantity: 3
Available
This board is a simple carrier of Broadcom’s bidirectional ±50A ACHS-7125 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. Pololu 4034
zł20.52
24h
Available quantity: 1
Available
ACS724LLCTR-20AU current sensor module with a current measurement range from 0 to 20 A. It communicates via an analog interface. Pololu 4044
zł52.36
24h
Available quantity: 2
Available
The module with the ACS725 current sensor with a direct current measuring range up to 10 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020616
zł52.62
24h
Available quantity: 3
Available
The current measurement with a value of 0 - 5A is realized by the ACS712-05 system based on the Hall effect. The system sensitivity is 185mV / A (analog signal).
zł8.66
24h
Available quantity: 20
Available
The module with the ACS70331 current sensor with a direct and alternating current measuring range ±5 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020615
zł64.99
6 weeks
No product available!
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
zł98.45
4 weeks
No product available!
Voltage and current sensor module. It works with a shunt resistor and voltage divider and the INA-169 chip and can measure voltages up to 52 V and currents up to 90 A. SparkFun SEN-16408
zł136.90
4 weeks
No product available!
Module with ACS724LLCTR-05AB current sensor with a measuring range of direct and alternating current from -5 to 5 A. It communicates via an analog interface. Pololu 4041
zł47.71
24h
Available quantity: 2
Available
Available
Module with an analog current sensor. Enables measurement of alternating and direct current up to 20 A. DFRobot SEN0214
zł45.46
24h
Available quantity: 1
Available
ACS724LLCTR-30AB current sensor module with a DC and AC measurement range from -30 to +30 A. It communicates via an analog interface. Pololu 4047
zł52.36
24h
Available quantity: 5
Available
ACS723 current sensor module with a DC and AC measuring range of ± 5 A. It can read very low currents of 10 mA. It communicates via the analog interface. SparkFun SEN-14544
zł117.16
4 weeks
No product available!
The current measurement with the value 0-20A is carried out by the ACS712-05 system based on the Hall effect. The sensitivity of the system is 100mV / A (analogue signal) .modACS712-20
zł14.18
24h
Available quantity: 3
Available
The module with a TA12-200 current sensor with a measuring range of alternating current up to 5 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020027
zł41.34
24h
Available quantity: 2
Available
Module with ACHS-7121 current sensor with a measuring range of direct and alternating current from -10 to 10 A. It communicates via an analog interface. Pololu 4030